User manual HUSQVARNA 343 FRM

[. . . ] Operator’s manual (EPA) 343F 345FX 345FXT 343FR 343FRM 343R 345RX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. [. . . ] When working at continuous high revs a higher octane rating is recommended. • • ! Fuel WARNING!Bear in mind the risk of fire, explosion and inhaling fumes. • Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). Never use oil intended for four-stroke engines. Mixing ratio 1:50 (2%) with HUSQVARNA two-stroke oil. Gasoline, litre 5 10 15 20 US gallon 1 2 1/2 5 Two-stroke oil, litre 2% (1:50) 0, 10 0, 20 0, 30 0, 40 US fl. The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. • • • ! WARNING!Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation. 22 – English FUEL HANDLING Mixing • • Always mix the gasoline and oil in a clean container intended for fuel. Always start by filling half the amount of the gasoline to be used. Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. Fueling ! WARNING!Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refuelling. Always move the machine away from the refuelling area before starting. • • • Do not mix more than one month’s supply of fuel at a time. If the machine is not used for some time the fuel tank should be emptied and cleaned. • • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WARNING! [. . . ] no. 343F, 345FX, 345FXT Approved accessories Centre hole in blades/cutters, Ø 20 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Maxi XS 200-22 (Ø 200 22 teeth) Saw blade Scarlet 200-22 (Ø 200 22 teeth) Scarlet 225-24 (Ø 225 24 teeth) Plastic blades Tricut Ø 300 mm Trimmy S Trimmer head Trimmy S II Auto 55 T45x Support cup Fixed With ball bearing 537 29 74-01 537 29 74-01 537 29 74-01 537 21 71-01 537 21 71-01 502 03 94-06 537 29 74-01 537 29 73-01 537 29 73-01 537 29 73-01 537 29 73-01 Cutting attachment guard, Art. no. English – 39 TECHNICAL DATA 343FR Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S II Trimmer head Auto 55 T45x Support cup Fixed With ball bearing 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. no. 343FRM Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S II Trimmer head Auto 55 T45x Support cup Shredder blade Fixed With ball bearing 544 02 65-02 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. no. 40 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2009 and later small nonroad engine. [. . . ]