User manual HUSQVARNA 346 XP EPA II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUSQVARNA 346 XP EPA II. We hope that this HUSQVARNA 346 XP EPA II user guide will be useful to you.

Lastmanuals help download the user guide HUSQVARNA 346 XP EPA II.


Mode d'emploi HUSQVARNA 346 XP EPA II
Download
Manual abstract: user guide HUSQVARNA 346 XP EPA II

Detailed instructions for use are in the User's Guide.

[. . . ] Operator’s manual (EPA) 346XP EPA II 353 EPA I Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Key to symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • • • Approved protective helmet Approved hearing protection Protective goggles or a visor If your machine bears this symbol it is equipped with a catalytic converter. [. . . ] Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc. Take great care when removing small branches and avoid cutting bushes (i. e. cutting many small branches at the same time). Small branches can be grabbed by the chain and thrown back at you, causing serious injury. • Never put a chain saw down while the engine is running unless you have it in clear view and the chain brake is on. Switch the engine off before leaving your chain saw for any length of time. • Basic cutting technique General • • • Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc. ) in case you have to move suddenly. Take great care when working on sloping ground. Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i. e. without any resistance from the chain during cutting, can lead to serious engine damage). • Cutting from above = Cutting on the pull stroke. • Cutting from below = Cutting on the push stroke. Cutting on the push stroke increases the risk of kickback. See instructions under the heading How to avoid kickback. Terms Cutting = General term for cutting through wood. Limbing = Cutting branches off a felled tree. Splitting = When the object you are cutting breaks off before the cut is complete. 18 – English SAFETY INSTRUCTIONS There are five important factors you should consider before making a cut: 1 Make sure the cutting equipment will not jam in the cut. Cut all the way through the log from above. Avoid letting the chain touch the ground as you finish the cut. Maintain full throttle but be prepared for what might happen. 2 Make sure the object you are cutting will not split. If it is possible (can you turn the log?) stop cutting about 2/3 of the way through the log. 3 Make sure the chain will not strike the ground or any other object during or after cutting. Turn the log and finish the cut from the opposite side. 4 Is there a risk of kickback? The log is supported at one end. There is a high risk that it will split. 5 Do the conditions and surrounding terrain affect how safely you can stand and move about? Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension. In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom. [. . . ] A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar. Low kickback saw chain is a chain which has only met the kickback performance requirements of ANSI B 175. 1 safety requirements for gasoline powered chain saws when tested on the representative sample of chain saws below 3. 8 cu. We recommend that you as a replacement use the listed chains or "Low kickback saw chains" which are available at your dealer. Bar Length, inches Pitch, inch 13 15 16 18 20 13 15 16 18 20 0, 325 0, 325 0, 325 0, 325 0, 325 0, 325 0, 325 0, 325 0, 325 0, 325 Max nose radius 10T 10T 10T 10T 10T 10T 10T 10T 10T 12T Husqvarna H25, Oregon 21BP/34LG or 34SL (not 13”) Husqvarna H30, Oregon 95VP Chain Note: For the chains above you are free to choose between 0, 050" and 0, 058" gauge drive link for the corresponding bar, see the table below. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 346 XP EPA II

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 346 XP EPA II will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag