User manual HUSQVARNA 532442118

[. . . ] YTH22V42LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 21-18 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] • Remove blade bolt by turning counterclockwise. • Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY. • Install and tighten blade bolt securely (45-55 Ft. torque). MANDREL ASSEMBLY BLADE IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED. BLADE BOLT (SPECIAL) STAR CENTER HOLE Fig. 14 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 15 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 13 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. DOCKING POSITION OIL DRAIN EXTENSION TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. [. . . ] 575 43 80-01 539 11 21-70 532 18 76-90 539 10 76-30 532 40 02-34 539 11 20-78 532 19 30-03 532 17 60-66 532 17 91-27 539 19 42-08 532 11 07-31 532 11 07-35 532 11 07-36 532 19 51-61 539 11 24-12 539 99 07-99 539 99 07-17 575 22 45-01 539 13 27-28 539 10 82-71 539 10 65-04 539 99 05-17 539 97 69-79 539 11 28-99 539 10 48-64 532 17 85-15 532 19 61-04 574 82 71-01 539 99 09-23 532 17 79-68 539 10 47-63 539 99 06-92 DESCRIPTION Deck w/Decals 42" Housing Assembly Washer-Spacer Screw, Washer Head Nut, Top Center Lock Blade, 14-5/8" Bolt, 7/16, Assy Blade Roller, Nose Rod, Roller, Nose Clip Retainer Discharge Chute - 42” Plastic Spring - Torsion Pin, Clevis 5/16 x 5. 19 Stud, Fasten w/ Anti- Rotate Confinement Plate Rhsnb 5/16-18 x 5/8 Gr. 5 Nut 5/16-18 Hex Nyloc Idler Bushing Pulley, Idler Hcs 3/8-16 x 3-1/2 Gr. 5 Heavy Washer Washer, 3/8 Flat Std Nut 3/8-16 Hex Nyloc Nut 5/16-18 Hex Flange Nyloc Washer, 7/16 Flat Washer, Flat Hardened Pulley, Idler Spec. Hub Arm, Idler, Blk Rhsnb 3/8-16 x 1-3/4 Gr. [. . . ]