User manual HUSQVARNA 7021 CH1 A

[. . . ] 7021CH1 Owner’s Manual 532 18 99-71 Rev. 2 06. 22. 04 BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Look for this symbol to point out impor tant safety precautions. [. . . ] If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. TO STOP ENGINE • To stop engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start. If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. MAX 1/3 TO START ENGINE NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. To start a cold engine, push primer three (3) times before trying to start. This step is not usually necessary when starting an engine which has already run for a few minutes. Hold operator presence control bar down to the handle and pull starter handle quickly. 9 • Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. Mow north–south one week, then change to east–west the next week. This helps prevent matting/graining of lawn. • MAINTENANCE BEFORE EACH USE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel system or add Stabilizer AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE * (if so equipped) ** Electric-Start mowers *** Power-Propelled mowers **** Use a scraper deck to clean under 1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil. 5 - And after each 5 hours of use. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer. • Follow the maintenance schedule in this manual. LUBRICATION CHART WHEEL ADJUSTER (ON EACH WHEEL) ➀ ➁ ENGINE OIL ➀ MULCHER DOOR HINGE PIN ➀ REAR DOOR HINGE BEFORE EACH USE 1. [. . . ] 1 2 3 4 5 6 7 8 9 11 12 13 14 16 18 28 31 32 35 36 38 40 41 PART NO. 532 18 45-88 532 16 99-11 532 17 52-62 532 15 87-55 532 17 54-36 532 15 04-95 532 19 17-30 532 18 06-26 532 14 52-12 532 18 07-67 812 00 00-58 532 13 70-54 532 18 05-04 532 06 77-25 532 18 55-74 532 18 55-79 532 13 20-10 532 18 94-07 532 15 15-21 532 18 01-84 873 80 04-00 532 13 70-90 532 15 15-20 DESCRIPTION Drive Control Assembly Bearing, Wheel Adjuster Pan Head Tapping Screw #10-24 x 2-3/4 Screw V-Belt Retainer, Spring Nut, Hex, Flanged 1/4-20 Hubcap Locknut Wheel & Tire Assembly E-Ring Pinion Dust Cover Washer 1/2 Selector Knob Drive Cover Hex Flange Nut Pulley, Drive Kit, Wheel Adjuster, LH (Includes Knob and Bearing) Gear Case Assembly, Complete Locknut 1/4-20 Spring, Tension Kit, Wheel Adjuster, RH (Includes Knob and Bearing) KEY NO. 54 55 57 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 PART NO. 532 18 97-65 532 17 57-39 532 18 88-15 532 18 34-97 * 532 18 34-98 * 532 18 34-99 532 18 35-00 532 18 35-01 532 18 35-02 532 18 35-03 532 18 35-04 532 18 35-05 532 18 35-06 532 18 35-07 532 18 35-08 532 18 35-09 532 18 35-10 532 18 35-11 532 18 35-12 532 18 35-13 532 18 35-14 DESCRIPTION Grassbag Assembly Driveshaft Cover Frame, Grassbag Case, Lower Case, Upper Gear, 27 Teeth Lever, Clutch Spring, Return Shaft, Input Dog, Movable Dog, Fixed Wire, Formed Bearing, Ball Fork, Shift Seal, Output Shaft Washer Seal, Case Bushing Shaft, Output Screw Seal, Input Shaft 19 * Use Dow Corning #709 to reseal Gear Case Halves. [. . . ]