User manual HUSQVARNA 7021 CM

[. . . ] 7021CM Owner’s Manual 532 19 39-64 10. 07. 04 BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Look for this symbol to point out impor tant safety precautions. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. [. . . ] To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL. • • • TO STOP ENGINE • To stop engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start. If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. MAX 1/3 TO START ENGINE NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. To start a cold engine, push primer three (3) times before trying to start. This step is not usually necessary when starting an engine which has already run for a few minutes. Hold operator presence control bar down to the handle and pull starter handle quickly. 8 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. [. . . ] 1 2 3 4 5 6 7 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 37 39 PART NO. 532 17 65-55 532 17 36-58 532 17 41-10 532 17 95-85 532 13 20-04 532 19 15-74 532 06 64-26 532 15 41-32 532 18 55-89 532 17 65-56 532 75 06-34 532 12 52-03 532 18 55-88 532 05 17-93 532 17 41-12 817 60 04-06 532 18 92-78 532 18 92-77 532 18 89-87 532 16 85-99 532 18 66-12 873 93 05-00 532 17 41-05 532 17 41-06 532 85 18-56 532 15 21-24 532 16 57-04 532 18 39-01 532 18 55-95 532 18 57-16 532 18 55-74 532 18 57-18 532 16 08-28 532 18 05-41 532 08 39-23 DESCRIPTION Control Bar Upper Handle (Includes Foam Grip) Lower Handle Rope Guide Nut, Hex 1/4-20 Handle Bolt Wire Tie Bracket, Housing Mulcher Door Engine Zone Control Cable Hex Washer Head Screw Up-Stop Bracket Handle Knob Hairpin Cotter Support Bracket Screw Axle Arm Assembly, Front, LH Axle Arm Assembly, Front, RH Rear Skirt Selector Spring, Front Rear Door Kit (Includes Springs) Locknut, Hex 5/16-18 Handle Bracket Assembly, LH Handle Bracket Assembly, RH Screw 1/4-20 x 3/8 Hinge Spring Wheel Adjusting Bracket, Front Spacer Clip-on Discharge Guard Selector Spring, Rear Selector Knob Axle Arm Assembly, Rear, LH Shoulder Bolt 5/16-18 Wheel Assembly, Front Flanged Locknut KEY NO. 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 59 61 62 65 66 67 --- PART NO. 532 18 88-13 532 08 86-52 532 16 57-66 532 16 57-67 532 18 41-93 532 15 04-06 532 10 73-39 532 18 06-26 532 18 57-17 532 18 01-83 532 18 97-88 532 14 72-86 532 16 36-62 532 85 10-84 532 85 02-63 532 85 10-74 532 18 90-28 532 18 45-90 --532 18 01-23 873 80 04-00 532 08 83-48 532 18 81-52 532 16 42-65 532 16 23-00 532 19 39-64 DESCRIPTION Frame, Grassbag Hinge Screw Spring, Rear Door, LH Spring, Rear Door, RH Door Bolt Hex Head Thread Rolling Screw 3/8-16 x 1 Danger Decal Hubcap, Front Wheel Axle Arm Assembly, Rear, RH Wheel Assembly, Rear Grassbag Hinge Rod Kit, Lawn Mower Housing (Includes Key Numbers 17, 18 and 46) Hex Head Screw 3/8-24 x 1-3/8 Grade 8 Helical Lockwasher Hardened Washer 21" Blade Blade Adapter Engine, Briggs & Stratton, Model Number 12H602 (For engine service and replacement parts, call Briggs & Stratton at 1-800-233-3723) Hubcap, Rear Wheel Locknut, Hex 1/4-20 Washer, Flat 3/8 O-Ring Grip, Foam Warning Decal (not shown) Owner’s Manual, English / French 1 inch = 25. 4 mm 17 NOTE: All component dimensions given in U. S. [. . . ]