User manual HUSQVARNA 954002701

[. . . ] Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. Be sure the area is clear of other people before mowing. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. [. . . ] The best time to mow your lawn is the early afternoon. At this time the grass has dried and the newly cut area will not be exposed to the direct sun. For best results, adjust the mower cutting height so that the mower cuts off only the top one-third of the grass blades (See Fig. For extremely heavy mulching, reduce your width of cut on each pass and mow slowly. • • MAX 1/3 • • • FIG. 15 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across or perpendicular to the first cut path. Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week. This will help prevent matting and graining of the lawn. FIG. 14 14 CUSTOMER RESPONSIBILITIES MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation Check Tire Pressure E S E S RS RS AG US N UR S UR OU HOU HO ASO TOR CH OUR O H A 0 S 8H SE 25 50 10 E EE 2H RY ERY ERY ERY RY OR OR ST F R VE BEF VE V V V SERVICE E FI E E E E BE DATES T R A C T 0 R Check for Loose Fasteners Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level/Recharge Clean Battery and Terminals Check Transaxle Cooling Adjust Blade Belt(s) Tension Adjust Motion Drive Belt(s) Tension Check Engine Oil Level Change Engine Oil 1, 2, 3 2 2 6 4 7 5 5 E N G I N E Clean Air Filter Clean Air Screen Inspect Muffler/Spark Arrester Replace Oil Filter (If equipped) Clean Engine Cooling Fins Replace Spark Plug Replace Air Filter Paper Cartridge Replace Fuel Filter 1, 2 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See "TO ADJUST BRAKE" in the Service and Adjustments section of this manual). TIRES • • • Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" on page 3 of this manual). Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. CENTER HOLE BLADE REMOVAL (See Fig. 16) • • • • • Raise mower to highest position to allow access to blades. Remove hex bolt, lock washer and flat washer securing blade. Install new or resharpened blade with trailing edge up towards deck as shown. Reassemble hex bolt, lock washer and flat washer in exact order as shown. torque). BLADE 5/8" BOLT OR PIN IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED. BLADE MANDREL ASSEMBLY FIG. [. . . ] 30 Day Replacement Part Warranty: Unless otherwise stated, replacement parts are warranted for 30 days from date of purchase. (2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna. (3) Alterations or modifications that affect the unit's performance, operation, safety, durability, change its intended use, or cause failure of compliance with current regulatory standards or applicable federal, state or local laws. (4) Use of parts or accessories which are not recommended by Husqvarna Forest & Garden Company. [. . . ]