User manual HUSQVARNA 954140014B

[. . . ] LR122 OWNER'S MANUAL SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. • • • • • • • • • • • • • • • GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. [. . . ] • Lower mower deck to lowest cutting position. • Remove retainer spring and washer that holds mower clutch spring to the mower clutch arm. • Disconnect mower clutch spring from mower clutch arm. • Remove retainer springs and washers from mower stabilizer link. • Remove retainer springs and washers from rear lift links. • Remove retainer spring and washer from front lift link. • Withdraw front lift link, rear lift links and mower stabilizer link from brackets. • Raise mower lift handle to transport position. • Slide mower deck out on right side of tractor. MOWER UPSTOP ADJUSTMENT (See Fig. 19) • Raise attachment lift lever to highest (transport) position. • Measure distance from top of mower deck to lower flange of chassis (dim. “A” should be 3-3/8 to 3-1/2 inches. “A”, if required, lower mower to lowest position. Remove washer and retainer spring in trunnion, then withdraw trunnion pin from bracket. Loosen trunnion locknut and rotate trunnion counterclockwise on lift link to increase dim. “A” or clockwise on lift link to decrease dim. NOTE: Each full turn of trunnion will change dim. • Re-insert trunnion into bracket with pin pointing to L. H. • Raise lift lever to highest position and recheck dim. Repeat adjustment if necessary. LOWER FLANGE OF CHASSIS “A” TOP OF MOWER DECK TO INSTALL MOWER (See Fig. 18) • Reverse removal instructions. ENGINE PULLEY MOWER CLUTCH SPRING BELT MOWER CLUTCH ARM AXLE BRACKET RETAINER SPRING WASHER FRONT LIFT TRUNNION RETAINER SPRING WASHER BRACKET TRUNNION LOCKNUT FIG. 19 MOWER STABILIZER LINK REAR LIFT LINKS FRONT LIFT LINK FIG. [. . . ] An authorized Husqvarna dealer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-HUSKY62 for a dealer in your area. SECTION 3: ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this warranty: (1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to, belts, blades, blade adapters, bulbs, filters, guide bars, lubricants, rewind springs, saw chain, spark plugs, starter ropes and tines; (2) Natural discoloration of material due to ultraviolet light; (3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer; (4) Lawn and garden attachments are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer; and (5) Emission Control System components necessary to comply with CARB-95 and EPA regulations which are manufactured by third party engine manufacturer. SECTION 4: EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following: (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; HUSQVARNA FOREST & GARDEN COMPANY 9006-J PERIMETER WOODS DRIVE CHARLOTTE, NC 28216 531 83 81-23 2/95 SERVICE ® POLICY WARRANTY LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS A. Products Warranted ® TECUMSEH Issued January 1980 Revised January 1991 TECUMSEH Peerless Gear and Machine Division of Tecumseh Products Company (“Tecumseh”), subject to the limitations contained below, will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and Series 1100 angle drive and ONE YEAR for all other Peerless products. New Power Train Components incorporated in equipment used for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to the original purchaser. B. [. . . ]