User manual HUSQVARNA 95414001A

[. . . ] Be sure the area is clear of other people before mowing. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. Be aware of the mower discharge direction and do not point it at anyone. [. . . ] • The attachment clutch should never operate unless the operator is in the seat. BLADE 5/8" BOLT OR PIN FIG. 16 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY” in the SERVICE AND ADJUSTMENTS section of this manual). BLADE CARE For best results mower blades must be kept sharp. For approximate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual. • Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished. FIG. 17) Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. Service air cleaner more often under dusty conditions. • Remove wing nut and air cleaner from base. [. . . ] 954 14 00-07 HYDRO GEAR TRANSAXLE - MODEL NUMBER 319-0650 KEY PART NO. 1 2 3 4 5 6 7 8 9 13 14 15 17 18 19 23 24 25 26 27 28 29 30 34 35 36 37 38 39 40 41 532142930 532142931 532142932 532142928 532142933 532142934 532142935 532150771 532142937 532142938 532142939 532142940 532142941 532150772 532150773 532142944 532142945 532142946 532150774 532142948 532142949 532142950 532150787 532142951 532142952 532142953 532142954 532142955 532150777 532150778 532142958 DESCRIPTION Housing, Lower Assembly, Upper Housing Seal, Lip Ring, Wire Retaining Ring, Retaining Bearing, Shaft Ball Bearing, Cradle Bearing, Thrust 30 x 52 x 13 Swashplate, Variable Block, Cylinder Assembly Arm, Trunnion Seal, Lip Guide, Slot Shaft, Motor Bearing, Thrust 42 x 68 x 16 Block, Cylinder Assembly Seal, Lip 10 x 25 x 7 Actuator, Bypass Center Section Assembly Kit Seal, Lip 26 x 42 x 8 Ring, Retaining Washer 26 x 35 x 1 Plate, Bypass Oil Filter Element Arm, Bypass Ring, Retaining Arm, Actuating Pin, Actuating Bolt 5/16-24 x 1-3/4 Locknut, Hex 5/16-24 UNJC Brake Rotor/Stator Kit KEY PART NO. 43 44 52 53 56 58 59 62 63 64 68 69 83 85 88 89 90 91 92 93 113 114 119 134 135 139 140 532142884 532150829 532142991 532142961 532142963 532142964 532142965 532142966 532142967 532142920 532142969 532144610 532142971 532150806 532142973 532142974 532142975 532142976 532142977 532142978 532142917 532142918 532142980 532144607 532144608 532150775 532150776 DESCRIPTION Washer 7/16 x 7/8 x . 060 Differential Assembly Washer 3/4 x 1. 5 x . 13 Seal . 75 x 1. 25 x . 250 Shaft, Input Bolt 1/4-20 x 1. 38 Pin . 5 OD x . 43 ID x . 750 Arm, Control Puck, Dampener Set Screw Spring Stud 5/16-24 Jackshaft Assembly Jackshaft Screw, Cap Washer 7/16 x 1 x 1/2 Sleeve Bearing Seal, Wiper Spring, Block Washer, Block Thrust Cap, Vent Assembly Fitting, O-Ring Assembly Spacer Nut, Castle 5/16-24 Pin, Cotter Spring, Compression Nut, Hex 5/16-24 NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 47 SERVICE NOTES 48 SERVICE NOTES 49 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION SIGHTING GUIDE CUT OUT ON D THIS OTT IS A ED L 15° S INES LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 50 15° MAX. SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. [. . . ]