User manual HUSQVARNA 954223077

[. . . ] 9027STE XP Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. Avoid loose, dangling portant safety precautions. [. . . ] Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. NOTE: Do not use primer when starting engine with the electric starter. Push starter button until engine starts. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. Wait 5 to 10 seconds between each attempt. When the engine starts, release the starter button and slowly move the choke control to the OFF position. Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Allow the engine to warm up for a few minutes. [. . . ] 1 inch = 25. 4 mm 29 REPAIR PARTS 10 24 14 22 23 21 20 13 11 2 3 4 33 26 25 10 27 28 WHEELS / DECALS SNOW THROWER - MODEL NO. 954 22 30-77 10 32 30 8 31 7 18 15 19 17 12 10 29 4 1 2 9 10 32 30 18 15 12 16 29 10 27 28 28 10 25 24 26 23 22 19 14 13 7 4 6 5 4 11 10 21 20 33 3 1 13 2 4 12 9 8 6 5 1 13 3 30 11 10 7 REPAIR PARTS KEY PART NO. NO. WHEELS / DECALS SNOW THROWER - MODEL NO. 954 22 30-77 DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 532 18 78-32 532 15 54-43 532 19 21-09 532 18 44-71 873 80 05-00 532 15 54-15 871 21 06-16 532 18 78-59 532 18 78-58 532 14 63-15 817 49 05-08 532 18 43-93 532 18 78-60 532 18 20-15 532 19 29-88 532 18 19-82 532 18 20-63 532 18 18-47 532 08 51-79 532 18 41-97 532 17 91-41 532 18 24-66 532 18 76-22 532 18 76-23 532 17 91-39 532 17 91-37 532 17 88-79 532 17 46-97 532 17 98-30 532 18 44-53 532 18 78-64 532 70 02-79 812 00 00-45 Wheel Assembly, 16", Power Steering, LH Pin, Klik 1/4 Cover, Power Steering Bolt, Shoulder #10-24 x 5/8 Nut, Lock 5/16-18 Washer, Flat 5/16 Screw, Hex Head 3/8-16 x 1 Bracket, Steering Cable, RH Bracket, Steering Cable, LH Screw, Hex Head 5/16-18 x 5/8 Screw, Hex Head 5/16-18 x 1/2 Link, Steering Lever Yoke, Steering Pin, Steering Lever Bellcrank Bracket Assembly, LH Steering Bracket Assembly, RH Steering Pin, Steering Bellcrank Retainer, Hairpin Bracket, Steering Driver, Wheel Ring, Wire Retainer Lobe, Wheel Slide, Clutch Spring, Clutch Slide Lobe, Axle Key, Square 1/4 Washer, Thrust (1") Bearing, Axle Spring, Return Wheel Assembly, 16", Power Steering, RH Clip, Retainer Ring, Retaining KEY PART NO. [. . . ]