User manual HUSQVARNA 954223470

[. . . ] 5521RS Owner’s Manual 532 18 72-39 Rev. 1 07. 28. 04 BY Printed in U. S. A. SAFETY RULES Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • Read, understand, and follow all instructions on the machine and in the manual(s) before starting. [. . . ] If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. MAX 1/3 ON ( ) OFF ON • FUEL VALVE LEVER • FIG. 14 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. Mow north to south one week then east to west the next week. This will help prevent matting and graining of the lawn. MAINTENANCE BEFORE EACH USE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel system or add Stabilizer AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE * (if so equipped) ** Electric-Start mowers *** Power-Propelled mowers **** Use a scraper deck to clean under 1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil. 5 - And after each 5 hours of use. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer. • Follow the maintenance schedule in this manual. LUBRICATION CHART ➁ ENGINE OIL ➀ MULCHER DOOR HINGE PIN BEFORE EACH USE 1. Check for loose fasteners. ➀ REAR DOOR HINGE LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”). IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELFLUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. ➀ HANDLE BRACKET MOUNTING PINS ➀ SPRAY LUBRICANT ➁ SEE “ENGINE” IN MAINTENANCE SECTION 10 MAINTENANCE LAWN MOWER Always observe safety rules when performing any maintenance. • • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. To check blade balance, drive a nail into a beam or wall. [. . . ] 1 inch = 25. 4 mm ROTARY LAWN MOWER - - MODEL NUMBER 5521RS (5521RSB) - PRODUCT NUMBER 954 22 34-70 20 ROTARY LAWN MOWER - - MODEL NUMBER 5521RS (5521RSB) - PRODUCT NUMBER 954 22 34-70 KEY NO. 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 27 28 29 30 31 32 PART NO. 532 18 97-41 532 19 02-84 532 18 76-53 532 18 82-79 532 18 55-92 532 75 06-34 532 18 22-12 532 13 20-10 532 18 73-53 532 18 90-74 532 18 59-13 532 18 72-13 532 14 53-54 532 05 70-79 532 16 15-84 532 16 16-02 532 16 45-54 532 19 06-22 812 00 00-22 532 16 33-65 532 16 99-11 532 16 45-55 532 05 78-08 532 05 21-60 812 00 00-58 532 18 05-04 532 06 77-25 532 18 81-52 532 18 07-53 DESCRIPTION Drive Control Assembly, Auto-Walk Cable, Drive Control Screw Cover, Top, Auto-Walk Drive Control Cover Drive Screw, Threaded, Rolled #10-25 x . 50 V-Belt Nut, Hex, Flanglock, Zinc Plated 3/8-16 Pulley Decal, Drive Control Decal, Drive Control Adjustment (bottom) Gear Case Assembly (See Breakdown) Pin, Spring, Thrust Washer, Hardened Rod, Connecting Spring, Extension Spring Selector Knob, Selector Spring E-Ring 7/8 Bearing, Support Bearing, Ball Retainer, Drive Assembly, Stamped Screw, Tapping, Hex Head 1/4-20 x . 75 Washer E-Ring 7/16 Cover, Dust, Wheel Washer 1/2 x 1-1/2 x . 134 O-Ring Wheel 9 x 2 KEY NO. 33 34 35 36 37 38 39 40 41 42 43 44 45 47 48 49 50 51 52 53 54 55 56 58 60 61 PART NO. [. . . ]