User manual HUSQVARNA 954224200

[. . . ] 524STE Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. Avoid loose, dangling portant safety precautions. [. . . ] Disconnect the power cord from the receptacle first, then from the engine. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Insert safety ignition key into the ignition slot until it clicks. Keep the extra safety ignition key in a safe place. Place throttle control in FAST position. Push the primer four (4) times if the temperature is below 15°F/–10°C, or two (2) times if temperature is between 15° and 50°F/–10°C and 10°C. If temperature is above 50°F/10°C, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: 13 ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. Disconnect the power cord from the receptacle first, then from the engine. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. [. . . ] 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 -532 19 21-93 532 17 88-30 817 49 04-08 532 17 92-56 532 18 78-53 532 18 04-01 532 17 92-40 873 80 05-00 532 18 40-86 532 18 71-01 532 19 21-10 532 17 88-90 532 70 02-79 532 17 90-65 532 18 40-85 874 78 06-24 532 18 40-74 532 18 40-84 871 02 05-12 532 18 11-56 532 18 40-73 532 18 80-02 532 19 29-08 532 05 70-79 532 19 22-75 532 19 21-47 812 00 00-02 DESCRIPTION Cover, Belt Cover, Toolbox Screw, Hex Head 1/4-20 x 1/2 Bolt, Shoulder 5/16-18 Bellcrank Shifter Screw, Hex Head 1/4-28 x 3/4 Arm, Auger Control Nut, Lock 5/16-18 Bellcrank Assembly Link, Speed Control Trunnion, Clutch Nut, Cage 3/8-16 Hairpin, Cotter 3/32 x 1/2 Pin, Bellcrank Bracket, Bellcrank Screw, Hex Head 3/8-16 x 1-1/2 Pivot Bracket, Impeller Idler Arm Pan, Frame Bottom Screw, Hex Head 5/16-18 x 3/4 Nut, Speed 5/16-18 Frame Assembly Plate, Frame End Shaft, Auger Control Washer, Hardened Roller Ring, Crescent E-Ring 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 532 18 10-44 Spring, Traction Idler 532 18 05-22 Pulley, Idler (2-1/4) --Engine, Tecumseh, Model Number LH195SP (Order parts from Engine manufacturer) 874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4 532 15 00-78 Screw, Hex Washer Head 5/16-18 x 3/4 532 05 92-89 Washer, Flat 873 93 05-00 Nut, Jam, Lock 5/16-18 532 17 53-30 Pin, Idler Pivot 532 17 90-92 V-Belt, Traction Drive 810 04 05-00 Washer, Lock 5/16 817 49 05-08 Screw, Hex Washer Head 5/16-18 x 1/2 532 17 92-59 Idler Arm Assembly, Impeller 532 08 51-79 Retainer, Hairpin 532 17 88-28 Spring, Brake 532 18 35-33 V-Belt, Impeller Drive 532 19 23-06 Screw, Hex Head 3/8-16 x 1-1/4 532 18 48-04 Arm, Idler 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2 532 17 53-31 Bushing, Idler Pivot 532 18 05-23 Pulley, Idler (2-3/4) 874 61 05-16 Screw, Hex Head 5/16-24 x 1 532 17 93-71 Spacer, Engine Pulley 532 18 04-78 Pulley, Engine, Traction Drive 532 17 91-57 Pulley, Engine, Impeller Drive 532 06 27-35 Washer, Flat 3/8 532 85 02-63 Washer, Lock 3/8 532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8 532 18 35-61 Guide, Belt 532 18 38-54 Power Cord (not shown) NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 29 REPAIR PARTS WHEELS / DECALS 1 2 SNOW THROWER - - MODEL NO. 954 22 42-00 4 5 6 4 3 4 6 2 5 4 1 10 2 4 9 8 6 5 1 10 3 30 7 REPAIR PARTS WHEELS / DECALS SNOW THROWER - - MODEL NO. NO. DESCRIPTION 1 2 3 4 5 6 532 18 78-31 532 15 54-43 532 18 78-66 532 14 63-15 532 17 98-30 532 17 46-97 Wheel Assembly, 13", LH Pin, Klik 1/4 Wheel Assembly, 13", RH Screw, Hex Head 5/16-18 x 5/8 Bearing, Axle Washer, Thrust, 1" NOTE: All component dimensions given in U. S. [. . . ]