User manual HUSQVARNA 954633545

[. . . ] 1027STE Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. Avoid loose, dangling portant safety precautions. [. . . ] Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. If temperature is above 50°F, priming is not necessary. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: 13 ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. Disconnect the power cord from the receptacle first, then from the engine. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. SNOW THROWING TIPS • • • • Always operate the snow thrower with the engine at full throttle. Full throttle offers the best performance. Go slower in deep, freezing or heavy wet snow. [. . . ] 954 63 35-45 1 532 18 10-44 Spring, Traction Idler 2 532 18 05-22 Pulley, Idler (2-1/4) 3 --Engine, Tecumseh, Model Number HMSK105 (Order parts from Engine manufacturer) 4 874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4 5 532 15 00-78 Screw, Hex Washer Head 5/16-18 x 3/4 6 532 05 92-89 Washer, Flat 7 873 93 05-00 Nut, Jam, Lock 5/16-18 8 532 17 53-30 Pin, Idler Pivot 9 532 17 90-92 V-Belt, Traction Drive 10 810 04 05-00 Washer, Lock 5/16 11 817 49 05-08 Screw, Hex Head 5/16-18 x 1/2 12 532 17 92-59 Impeller Idler Arm Assembly 13 532 08 51-79 Retainer, Hairpin 14 532 17 88-28 Spring, Brake 15 532 18 35-33 V-Belt, Impeller Drive 16 532 15 04-06 Screw, Hex Head 3/8-16 x 1-1/4 17 532 18 48-04 Arm, Idler 18 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2 19 532 17 53-31 Bushing, Idler Pivot 20 532 18 05-23 Pulley, Idler (2-3/4) 21 874 61 05-16 Screw, Hex Head 5/16-24 x 1 22 532 17 93-71 Spacer, Engine Pulley 23 532 18 04-78 Pulley, Engine, Traction Drive 24 532 17 91-57 Pulley, Engine, Impeller Drive 25 532 06 27-35 Washer, Flat 3/8 26 532 85 02-63 Washer, Lock 3/8 27 532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8 28 532 18 35-61 Guide, Belt 29 532 18 04-65 Cover, Belt 30 532 17 88-30 Cover, Toolbox 31 817 49 04-08 Screw, Hex Head 1/4-20 x 1/2 32 532 17 92-56 Bolt, Shoulder 5/16-18 33 532 18 78-53 Bellcrank Shifter 34 532 18 04-01 Screw, Hex Head 1/4-28 x 3/4 35 532 17 92-40 Arm, Auger Control 36 873 80 05-00 Nut, Lock 5/16-18 37 532 18 40-86 Bellcrank Assembly 38 532 18 71-01 Link, Speed Control 39 532 17 90-64 Trunnion, Clutch 40 532 17 88-90 Nut, Cage 3/8-16 41 532 70 02-79 Pin, Cotter 3/32 x 1/2 42 532 17 90-65 Pin, Bellcrank 43 532 18 40-85 Bracket, Bellcrank 44 874 78 06-24 Screw, Hex Head 3/8-16 x 1-1/2 45 532 18 40-74 Pivot Bracket, Impeller Idler Arm 46 532 18 40-84 Pan, Frame Bottom 47 871 02 05-12 Screw, Hex Head 5/16-18 x 3/4 48 532 18 11-56 Nut, Speed 5/16-18 49 532 18 40-73 Frame Assembly 50 532 18 80-02 Plate, Frame End 51 532 18 40-82 Shaft, Auger Control 52 532 05 70-79 Washer, Hardened 53 532 17 90-62 Roller 54 812 00 00-10 Ring, Retaining - - 532 18 38-54 Power Cord (not shown) NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 29 REPAIR PARTS WHEELS / DECALS 1 2 SNOW THROWER - - MODEL NO. 954 63 35-45 4 5 6 4 3 4 6 2 5 4 1 10 2 4 9 8 6 5 1 10 3 30 7 REPAIR PARTS WHEELS / DECALS SNOW THROWER - - MODEL NO. NO. DESCRIPTION 1 2 3 4 5 6 532 18 78-33 532 15 54-43 532 18 78-65 532 14 63-15 532 17 98-30 532 17 46-97 Wheel Assembly, 16", LH Pin, Klik 1/4 Wheel Assembly, 16", RH Screw, Hex Head 5/16-18 x 1/2 Bearing, Axle Washer, Thrust, 1" NOTE: All component dimensions given in U. S. [. . . ]