User manual HUSQVARNA 96042003600

[. . . ] IMPORTANT MANUAL Do Not Throw Away 02478 OPERATOR'S MANUAL MODEL: 96042003600 WARNING: Read this Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PB195H42LT LAWN TRACTOR Visit our website: www. poulan-pro. com ALWAYS WEAR EYE PROTECTION DURING OPERATION 411287 12. 19. 06 TH Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Install and tighten blade bolt securely (45-55 Ft. IMPORTANT: Special blade bolt is heat treated. BLADE STAR 02 54 5 MANDREL ASSEMBLY BLADE BOLT (SPECIAL) CENTER HOLE FIG. 11) NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and eventual damage to mower and engine. • The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer. ) NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not. 828 16 MAINTENANCE • Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. F SAE VISCOSITY GRADES SAE 30 5W-30 -20 -30 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 CENTER HOLE BLADE C TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e FIG. 12 NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. 12 and 13) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. [. . . ] Nut Lock Flg 3/8-16 unc Washer Hardened . 793 x 1. 637 x KEY NO. PART NO. DESCRIPTION . 060 Bolt Hex HS 3/8-16 unc x 2-1/4 Spacer Brace Axle Bracket Upstop Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/8-11 Draglink LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Brace Axle Front Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. 5 Washer 1. 5 x . 505 x . 118 Bracket Deck Susp. 5 54 55 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 74760636 197636 407465 194747 194748 73971000 194740 194741 17000512 199849 194734 71020748 194737 73900700 199162 196197 196075 74780572 NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 12 REPAIR PARTS TRACTOR - - MODEL NUMBER PB195H42LT (96042003600), PRODUCT NO. [. . . ]