User manual HUSQVARNA 96043009100

[. . . ] 03002 GTH27V52LS Owner's Manual 532 43 26-53 Rev. 2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 15 15 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. DOCKING POSITION OIL DRAIN EXTENSION TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. 02 46 3 CAP 2. 7. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 Fig. [. . . ] 960 43 00-91 MOWER DECK 52 33 17 24 53 57 18 19 31 30 47 25 34 43 45 46 56 16 27 33 24 15 35 49 59 16 37 39 38 61 36 44 1 48 23 22 51 50 6 55 3 32 5 4 21 54 20 62 63 58 2 60 8 9 29 28 10 11 13 14 7 12 52F-tex_elec_3 40 TRACTOR - MODEL NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 33 34 PART NO. 575 43 80-03 539 11 21-70 539 10 75-20 532 10 75-21 539 10 75-90 539 10 76-30 532 11 07-33 532 11 07-35 532 11 07-36 574 87 08-01 539 10 75-22 574 87 50-02 539 99 07-99 539 99 07-17 532 19 51-61 539 11 28-99 532 19 61-04 574 84 18-02 532 17 79-68 539 13 27-28 575 22 45-01 539 10 76-10 539 10 76-08 521 99 65-01 575 22 47-02 539 10 47-63 539 10 82-71 539 10 65-04 539 99 05-17 539 97 69-79 539 99 09-23 539 10 48-64 532 17 85-15 DESCRIPTION Deck w/ Decals 52" Housing Assembly Washer-Spacer Pulley, Mandrel Nut, 9/16 Top Center Lock Screw, Washer Head Discharge Chute, 52" Spring - Torsion Pin, Clevis 5/16 x 5. 19 Blade, 16-1/4" Bolt, 7/16, Assy Blade Confinement Plate Rhsnb 5/16-18 x 5/8 Gr 5 Nut 5/16-18 Hex Nyloc Stud, Fasten w/ Anti- Rotate Nut 5/16-18 Hex Flange Nyloc Pulley, Idler Spec. Hub Arm, Idler, Blk Pulley, Idler Pulley, Idler Idler Bushing Wheel, Gauge Bolt, Shoulder Nut 3/8-16 Hex Flg Nyloc Shield, Belt LH Retainer 5/16c U Type Hcs 3/8-16 x 3-1/2 Gr 5 Heavy Washer Washer, 3/8 Flat Std Nut 3/8-16 Hex Nyloc Rhsnb 3/8-16 x 1-3/4 Gr 5 Washer, 7/16 Flat Washer, Flat Hardened KEY NO. [. . . ]