User manual HUSQVARNA 96043011201

[. . . ] 07002 YTH22V46XLS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 16-52 Rev. 2 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. [. . . ] • Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. • Install and tighten blade bolt securely (45-55 Ft. Lbs. ). MANDREL ASSEMBLY BLADE IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED. BLADE BOLT (SPECIAL) STAR CENTER HOLE Fig. 14 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 13 BLADE CARE For best results mower blades must be kept sharp. Replace bent or damaged blades. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. 15 MAINTENANCE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. [. . . ] inches 1 inch = 25. 4 mm 39 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011201), PRODUCT NO. 960 43 01-12 MOWER DECK 40 46 145 59 34 68 57 2 147 62 117 116 36 241 30 119 1 200 40 242 244 245 118 56 197 55 33 32 46 31 243 3 40 119 21 198 117 116 21 21 40 188 189 69 21 189 6 19 188 15 69 6 19 13 11 69 14 199 69 29 27 21 69 21 23 69 24 25 26 46_tex_lt_pred_25_r1 8 40 TRACTOR - - MODEL NUMBER YTH22V46XLS (96043011201), PRODUCT NO. 960 43 01-12 MOWER DECK KEY PART NO. 1 2 3 6 8 11 13 14 15 19 21 23 24 25 26 27 29 30 31 32 33 34 36 40 46 55 56 57 59 62 532 44 24-05 532 40 55-07 532 40 55-06 532 19 51-86 532 19 30-03 532 40 53-80 532 19 28-72 532 18 72-81 532 11 04-85 532 19 65-39 873 68 05-00 532 19 25-57 532 10 53-04 532 19 70-26 532 11 04-52 532 40 53-57 532 13 14-91 532 17 39-84 532 18 76-90 532 19 74-73 532 40 02-34 872 11 06-12 532 19 73-79 873 90 06-00 532 13 77-29 532 19 72-49 532 19 90-92 817 00 06-16 532 14 10-43 874 52 06-36 DESCRIPTION Mower Housing Cover Mandrel RH Cover Mandrel LH Arm Suspension Bolt/Washer asm 7/16-20 unf Blade Mower Hi Lift Shaft Assembly, Mandrel Housing, Mandrel Bearing, Ball, Mandrel Bolt, Shoulder Nut Bracket, Deflector Cap, Sleeve Spring, Torsion, Deflector Nut, Push Shield, Deflector Rod, Hinge Screw Thdrol Rolling Wsh Hd Washer, Spacer Pulley, Mandrel Nut, Toplock, Flanged Bolt Carr Sh. [. . . ]