User manual HUSQVARNA 96043011800

[. . . ] 07002 GTH26V52LS Owner's Manual 532 44 04-16 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. [. . . ] 16 Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 15 15 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TO OPEN TO CLOSE OIL DRAIN VALVE TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. 4 79 02 DRAIN TUBE • • • • TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 Fig. [. . . ] Washer, Lock Hvy Hlcl Spr 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Adapter, Wheel Steering Steering Support Lower Insert, Wheel Steering Screw 3/8-16 x 3/4 Gear, Sector Plate Washer 9/16 x 2-3/8 x 12 Ga. Nut Lock Flange 3/8-16 unc Nut Hex Jam Toplock 1/2-20 unf Washer Hardened . 793 x 1. 637 x . 060 Bolt Hex 3/8-16 unc x 2-1/4 Bolt Hex 3/8-16 unc x 2-1/4 Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/8-11 Draglink, LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Brace Axle Front Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. 5 Washer 1. 5 x . 505 x . 118 Bracket Deck Susp. Front Washer Thrust NOTE: All component dimensions given in U. S. [. . . ]