User manual HUSQVARNA 96083000501

[. . . ] FT900 Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine. " 532 43 99-99 SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers TRAINING • • • • • • • • • • Read the Owner’s Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. [. . . ] 10 MAINTENANCE BE FO RE EA EV CH ER US Y5 E HO EV ER UR Y2 S 5H EV OU ER RS Y5 0H OU RS MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Engine Oil Level Change Engine Oil Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge Clean Engine Cylinder Fins Replace Spark Plug SERVICE DATES 1, 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year you should replace the spark plug, clean or replace air filter, and check tines and belt for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART  TINE CONTROL  ENGINE BEFORE EACH USE • • • Check engine oil level.  IDLER ARM LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”) . SAE 30 OR 10W-30 MOTOR OIL REFER TO MAINTENANCE “ENGINE” SECTION 10 MAINTENANCE Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 OIL DRAIN PLUG engine_ar t_12 OIL LEVEL OIL FILLER PLUG TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE Fig. 12 NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F (0°C). Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tiller is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each five (5) hours of continuous use. Tighten oil filler plug securely each time you check the oil level. 11 and 12) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tiller is on level surface. • Oil will drain more freely when warm. [. . . ] 21 22 23 24 25 26 27 28 29 30 31 32 41 42 PART NO. 873 35 06-00 532 16 18-06 532 17 53-77 874 76 06-20 532 10 69-68 873 35 05-00 873 22 04-00 810 04 04-00 532 10 92-27 823 20 04-04 532 10 11-89 532 15 12-23 532 18 03-07 532 13 89-09 DESCRIPTION Nut, Hex, Jam 3/8-16 Pulley, Idler Arm, Idler Bolt 3/8-16 x 1-1/4 Shaft, Idler Arm Nut, Hex, Jam 5/16-18 Nut, Hex 1/4-20 Washer, Lock 1/4 Pad, Idler Screw, Set , Socket, Headless C. P 1/4-20 x 1/4 . Sheave, Engine Sheave, Transmisison Spring Extension Spacer NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 19 REPAIR PARTS TILLER - MODEL NO. [. . . ]