User manual HUSQVARNA 96093001200

[. . . ] DRT900H Owner's Manual / 96093001200 / 2009-12 532 43 08-18 SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers • TRAINING • • • • • • • • • • Read the Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. Never allow children to operate the equipment. [. . . ] • Place throttle control in “FAST” position. • Push fuel valve to “ON” position. • Turn engine switch to “ON” position. • Move choke control to full “CHOKE” position. • Grasp recoil starter handle with one hand and grasp tiller handle with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). • Pull recoil starter handle quickly. Do not let starter handle snap back against starter. • • 10 OPERATION • Do not lean on handle. This takes weight off the wheels and reduces traction. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake. ADJUST WHEELS FOR CULTIVATING (See Figs. 17 and 18) • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch until hole in inner wheel hub lines up with inner hole in axle. • Replace clevis pin and hairpin clip on inside of wheel and remove blocks. • Repeat preceding steps on left hand side. NOTE: In extremely rough conditions and while cultivating, the wheels should be moved outward on the axle for increased stability. OUTER VIEW OF TIRE CLEVIS PIN 4 5 3 6 2 7 1 Fig. 15 CULTIVATING Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Best digging depth is 1" to 3" (2. 5-7. 5 cm). Lower the outer side shields to protect small plants from being buried. • Cultivate up and down the rows at a speed which will allow tines to uproot weeds and leave the ground in rough condition, promoting no further growth of weeds and grass (See Fig. • Do not lean on handle, this takes weight off the wheels, reduces traction, and may cause the tiller to skip over the ground. • Always lower the drag stake when using the forward rotating tine drive. HAIRPIN CLIP tire_1 Fig. [. . . ] inches 1 inch = 25. 4 mm 22 REPAIR PARTS TRANSMISSION TILLER - - MODEL NUMBER DRT900H (96093001200), PRODUCT NUMBER 960 93 00-12 KEY PART NO. DESCRIPTION 1 532 18 82-40 Transmission Assembly (Includes Key Nos. 4) 3 532 43 10-22 Gasket, Gearcase 4 532 00 50-20 Bearing, Needle 5 532 00 13-70 Washer, Thrust 5/8 x 1. 10 x 1/32 6 532 16 15-20 Pinion, Input 7 532 16 15-18 Shaft, Input 8 532 00 48-95 Bearing, Needle 9 532 15 44-67 Washer, Seal 10 532 00 73-92 Ball, Steel 11 532 10 03-71 Spring, Shift, Fork 12 532 10 61-60 O-Ring 13 532 14 21-45 Arm, Shift 14 532 00 83-53 Fork, Shift 15 812 00 00-39 Ring, Klip 16 532 16 15-16 Shaft, Shift 18 532 00 43-58 Washer 19 812 00 00-40 Ring, Klip 20 532 10 21-14 Gear, Assembly, Reverse Idler (Includes Key Nos. 21 and 22) 21 532 10 21-15 Gear, Reverse Idler 22 532 00 68-03 Bearing, Needle 23 532 16 15-27 Shaft, Reverse Idler 24 810 04 07-00 Washer, Lock 7/16 25 873 61 07-00 Nut, Hex 7/16-20 27 523 14 30-09 Bearing, Shaft, Ground Drive L. H. [. . . ]