User manual HUSQVARNA 96093001401

[. . . ] DRT900E Owner's Manual 532 43 99-74 SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers • TRAINING • • • • • • • • • • Read the Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly. Never allow children to operate the equipment. [. . . ] A tiller will also clear the soil of unwanted vegetation. The decomposition of this vegetable matter enriches the soil. Depending on the climate (rainfall and wind), it may be advisable to till the soil at the end of the growing season to further condition the soil. You will find tilling much easier if you leave a row untilled between passes. 15) There are two reasons for doing this. First, wide turns are much easier to negotiate than about-faces. Second, the tiller won’t be pulling itself, and you, toward the row next to it. Soil conditions are important for proper tilling. Tines will not readily penetrate dry, hard soil which may contribute to excessive bounce and difficult handling of your tiller. Hard soil should be moistened before tilling; however, extremely wet soil will “ball-up” or clump during tilling. Wait until the soil is less wet in order to achieve the best results. When tilling in the fall, remove vines and long grass to prevent them from wrapping around the tine shaft and slowing your tilling operation. This takes weight off the wheels and reduces traction. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake. Fig. 16 • • Do not lean on handle, this takes weight off the wheels, reduces traction, and may cause the tiller to skip over the ground. Always lower the drag stake when using the forward rotating tine drive. • • ADJUST WHEELS FOR CULTIVATING (See Figs. 17 and 18) • • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch until hole in inner wheel hub lines up with inner hole in axle. • Replace clevis pin and hairpin clip on inside of wheel and remove blocks. • Repeat preceding steps on left hand side. NOTE: In extremely rough conditions and while cultivating, the wheels should be moved outward on the axle for increased stability. OUTER VIEW OF TIRE CLEVIS PIN 4 5 3 6 2 7 1 tire_1 HAIRPIN CLIP Fig. 15 INNER VIEW OF TIRE CLEVIS PIN CULTIVATING Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. [. . . ] inches 1 inch = 25. 4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 23 REPAIR PARTS TRANSMISSION TILLER - - MODEL NUMBER DRT900E (96093001401), PRODUCT NUMBER 960 93 00-14 KEY PART NO. DESCRIPTION 1 532 18 82-40 Transmission Assembly (Includes Key Nos. 4) 3 532 43 10-22 Gasket, Gearcase 4 532 00 50-20 Bearing, Needle 5 532 00 13-70 Washer, Thrust 5/8 x 1. 10 x 1/32 6 532 16 15-20 Pinion, Input 7 532 16 15-18 Shaft, Input 8 532 00 48-95 Bearing, Needle 9 532 15 44-67 Washer, Seal 10 532 00 73-92 Ball, Steel 11 532 10 03-71 Spring, Shift, Fork 12 532 10 61-60 O-Ring 13 532 14 21-45 Arm, Shift 14 532 00 83-53 Fork, Shift 15 812 00 00-39 Ring, Klip 16 532 16 15-16 Shaft, Shift 18 532 00 43-58 Washer 19 812 00 00-40 Ring, Klip 20 532 10 21-14 Gear, Assembly, Reverse Idler (Includes Key Nos. 21 and 22) 21 532 10 21-15 Gear, Reverse Idler 22 532 00 68-03 Bearing, Needle 23 532 16 15-27 Shaft, Reverse Idler 24 810 04 07-00 Washer, Lock 7/16 25 873 61 07-00 Nut, Hex 7/16-20 27 523 14 30-09 Bearing, Shaft, Ground Drive L. H. [. . . ]