User manual HUSQVARNA 96143001901

[. . . ] 65021CHV Owner’s Manual 532 41 10-43 12. 07. 06 BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Look for this symbol to point out important safety precautions. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. [. . . ] Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the early afternoon. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. MAX 1/3 TO START ENGINE NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. To start a cold engine, push primer three (3) times before trying to start. This step is not usually necessary when starting an engine which has already run for a few minutes. Hold operator presence control bar down to the handle and pull starter handle quickly. 9 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Change your cutting pattern from week to week. Mow north–south one week, then change to east–west the next week. This helps prevent matting/graining of lawn. • • MAINTENANCE BEFORE EACH USE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel system or add Stabilizer AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE * (if so equipped) ** Electric-Start mowers *** Power-Propelled mowers **** Use a scraper deck to clean under 1 - Change more often if operating under a heavy load or in high outdoor temperatures. 2 - Service more often if operating in dirty or dusty conditions. 3 - Replace blades more often when mowing in sandy soil. 5 - And after each 5 hours of use. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. [. . . ] Failure to do so could be hazardous, damage your lawn mower and void your warranty. ROTARY LAWN MOWER - - MODEL NUMBER 65021CHV (96143001901) - PRODUCT NUMBER 961 43 00-19 18 ROTARY LAWN MOWER - - MODEL NUMBER 65021CHV (96143001901) - PRODUCT NUMBER 961 43 00-19 KEY NO. 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 17 18 25 26 27 28 29 32 33 PART NO. 532 40 73-16 532 41 16-73 532 40 62-62 532 19 00-39 532 41 16-64 532 18 16-98 532 40 07-23 532 40 62-59 532 18 93-78 532 41 10-81 812 00 00-58 532 40 38-49 532 18 94-03 532 19 10-17 532 06 77-25 532 40 48-31 532 70 10-37 532 41 16-63 532 16 34-09 532 17 52-62 DESCRIPTION KEY NO. 35 36 38 40 41 54 55 57 60 61 62 63 64 65 66 67 68 69 70 71 73 74 78 79 PART NO. DESCRIPTION Drive Control Assembly Cover, Drive Control, Upper Pulley Lever, Drive Control Cover, Drive Control, Lower Screw Mounting Bracket, Drive Control Cable, Drive Decal, Drive Control Wheel & Tire Assembly E-Ring Pinion Dust Cover Pawl, Drive Washer 1/2 x 1-1/2 x . 134 Bearing, Wheel Adjuster Selector Knob Belt Keeper Screw Screw, Pan Head, Self-Tapping #10-24 x 2-3/4 532 18 57-15 Drive Cover 532 1941-49 V-Belt 532 19 40-18 Drive Pulley 532 08 39-23 Locknut, Hex 532 40 91-08 Kit, Wheel Adjuster, LH (Includes Knob and Bearing) 532 40 48-33 Gearcase Assembly, Complete 873 80 04-00 Locknut, Hex 1/4-20 532 40 65-58 Spring 532 40 91-09 Kit, Wheel Adjuster, RH (Includes Knob and Bearing) 532 40 11-90 Grassbag Assembly 532 17 57-39 Driveshaft Cover 532 40 18-02 Frame, Grassbag 532 19 35-57 Decal, Drive Cover 532 41 07-26 Case, Upper 532 41 09-49 Shaft, Output 532 18 35-08 Seal, Output Shaft 532 18 35-11 Bushing 532 18 35-09 Washer 532 18 35-14 Seal, Worm Shaft 532 18 35-06 Bearing, Ball 532 41 07-29 Gear, 28 Teeth 532 41 07-32 Fixed Dog Clutch 532 41 07-33 Pin 532 41 07-30 Movable Dog Clutch 532 18 35-13 Screw, Case 532 41 07-34 Case, Lower 532 41 07-31 Spring, Leaf 532 41 07-27 Shaft, Worm 19 NOTE: All component dimensions given in U. S. [. . . ]