User manual HUSQVARNA 96145000200

[. . . ] 5521BBC Owner’s Manual 532 19 45-38 Rev. 6 05. 19. 05 BY/BY/BY/TR/BY/BY/BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Look for this symbol to point out important safety precautions. [. . . ] Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • MOWING TIPS CAUTION: Do not use de-thatcher blade attachments. Such attachments are hazardous, will damage your mower and could void your warranty. Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings. It may also be necessary to reduce ground speed and/or run the lawn mower over the area a second time. For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly. For better grass bagging and most cutting conditions, the engine speed should be set in the fast position. Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dry before using. Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life. • • • • MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL. TO STOP ENGINE • To stop engine, move throttle control lever to STOP position. Wait until blade and all moving parts have stopped and turn fuel valve to OFF position if you do not intend to restart the engine soon. • TO START ENGINE (See Fig. 14) NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. [. . . ] 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO. 532 18 97-41 532 18 82-79 532 18 73-53 532 19 00-39 532 18 82-78 532 18 16-98 532 18 70-97 532 18 62-97 532 19 02-84 532 18 90-74 532 18 59-13 532 18 76-53 532 18 86-45 532 18 94-08 532 13 20-10 532 16 15-84 532 16 16-02 532 19 07-94 532 19 06-22 812 00 00-22 532 16 33-65 532 16 99-11 532 16 45-55 532 05 78-08 532 19 05-14 532 75 06-34 532 05 21-60 812 00 00-58 532 18 94-03 532 17 51-04 532 18 41-72 DESCRIPTION Drive Control Assembly, Auto-Walk Cover, Top, Auto-Walk Drive Control Pulley Lever, Auto-Walk Drive Control Cover, Bottom, Auto-Walk Drive Control Screw, Phillips Head #10 x 5/8 Plate, Trigger, Auto-Walk Drive Control Cap, Drive Control, Bottom Cable, Drive Control Decal, Drive Control Decal, Drive Control Adjustment (bottom) Screw Gear Case Assembly, Complete Pulley, Drive Nut, Hex, Flanglock, Zinc Plated 3/8-16 Rod, Connecting Spring, Extension Spring Selector Knob, Selector Spring E-Ring Bearing, Support Bearing, Ball Retainer, Drive Assembly, Stamped Screw, Tapping, Hex Head 1/4-20 x . 75 Cover Drive Screw, Threaded, Rolled #10-25 x . 50 Washer E-Ring 7/16 Cover, Dust, Wheel Disc, Drive Seal, Friction KEY NO. 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 PART NO. 532 18 07-74 532 08 39-23 532 18 06-26 532 19 12-05 532 16 45-50 532 16 14-63 532 16 34-09 532 70 02-79 532 15 03-39 532 18 83-30 532 14 52-12 532 18 83-31 532 18 22-12 532 17 50-98 532 18 82-91 532 06 77-25 532 17 51-05 532 17 51-03 532 17 51-02 532 18 75-30 532 18 75-31 532 18 75-32 532 18 75-33 532 18 35-05 532 18 35-06 532 18 35-08 532 18 35-09 532 18 35-11 532 19 12-49 532 18 35-13 532 18 35-14 DESCRIPTION Wheel, Driven, Rear 9 x 2 Nut, Hex, Flangelock 3/8-16 Hubcap Shaft Assembly, Rear Shaft Assembly, Front Retainer, Front Shaft Screw #12 x 5/8 Clip, Retainer Wheel, Front 8 x 2 Pinion Assembly, RH Nut, Hex Pinion Assembly, LH V-Belt Pawl Spring, Torsion Washer 1/2 x 1-1/2 x . 134 Retainer, Drive, LH Gear, Pinion Retainer, Drive, RH Case, Lower Case, Upper Gear, 24 Teeth Shaft, Input Wire, Formed Bearing, Ball Seal, Output Shaft Washer Bushing Shaft, Output Screw Seal, Input Shaft 19 NOTE: All component dimensions given in U. S. [. . . ]