User manual HUSQVARNA 965997001

[. . . ] Modifications to the unit may cause unsafe operations or damage the unit. ©2008 HTC. Printed in U. S. A. Contents INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driving and Transport on Public Roads. . . . . . . . . . . . . . . . . . . . . . . 5 Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When both controls are in the neutral position, the machine stands still. By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively. In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right. Turning on the spot (zero turn) can be achieved by moving one control backward (behind the neutral position) and carefully moving the other steering control forward from its neutral position. ST FA CHOKE UP BLADES ON DOWN BLADES OFF OW SL Set blade engagement and throttle control 8052-001 Operating On Hills Read the Safety Instructions “Driving on Slopes” in the “Safety Instructions”. Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes. • • • The slowest speed possible should be used before starting up or down hills. Avoid stopping or changing speed on hills. If stopping is absolutely necessary, pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake. Place controls in neutral position 8061-026 IMPORTANT INFORMATION Control levers return to neutral when released. This may cause the mower to suddenly stop. • • • To restart movement, release the parking brake. Avoid sudden directional changes. Husqvarna-31 operation Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling. • Disengage the mower deck by depressing the blade switch. ST FA CHOKE UP BLADES ON DOWN BLADES OFF OW SL Disengage the mower deck and move throttle to minimum 8052-001 • • Raise the mower deck by pressing the button on the lever and pullng backward to the transport position. When the machine is standing still, activate the parking brake by pushing the lever button and pulling the lever upward. Move the throttle to the minimum position (tortoise symbol). Turn the ignition key to the stop position. • The mower deck’s lifting lever 8058-019 • • Move the steering controls outward. Always remove key when leaving the mower to prevent unauthorized use. IMPORTANT INFORMATION Leaving the ignition switch in any other position than “OFF” will cause the battery to be discharged. Place controls in neutral position 32-Husqvarna 8061-026 operation Manual Transport ZT-2800 Bypass Linkages When pushing or pulling the mower, engage the ZT-2800 (Integrated Zeroturn Transaxle) bypass linkages. The ZT-2800 bypass linkages are located on the rear of the frame, below the rear engine guard. 1. Raise the deck into the highest cutting position. 2. Pull the ZT-2800 bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position. [. . . ] (6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are manufactured by third party engine manufacturer. SECTION 4 - EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following: (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; (2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna; (3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or: (4) Additional damage to parts or components due to continued use occurring after any of the above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. HUSQVARNA SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THESE PRODUCTS EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. [. . . ]