User manual HUSQVARNA C42C

[. . . ] Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion. comm un ra re er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChec ende less tion. [. . . ] Fold flaps to inside of carton and turn carton upsidedown on floor of work area. To protect grass catcher cover during assembly place cover upsidedown on overturned carton. Be sure all parts are there. CARTON CONTENTS: (2) Container Tops (2) Container Bottoms (1) Upper Chute (1) Lower Chute (1) Support Post (1) Mounting Bracket (1) Cover Assembly (1) Cover Seal (1) Bag of Parts (1) Owner's Manual · NOTE: For ease of assembly, aside of your work area, lay out all hardware in the following groups. Each step of the assembly instructions will identify the group needed for that step. BAG OF PARTS CONTENTS ASSEMBLY LOCATION HARDWARE SHOWN ACTUAL SIZE GROUP "A" REAR MOUNTING BRACKET TO DRAW BAR (4) Shoulder Bolt 5/16 - 18 Self Tapping (4) Bolt 5/16 - 18 x 3/4 (4) Locknut 5/16-18 GROUP "B" SUPPORT POST TO CONTAINER SUPPORT (3) Carriage Bolt 5/16 - 18 x 3/4 (3) Locknut 5/16-18 GROUP "C" SUPPORT POST TO MOUNTING BRACKET (1) Bracket Support Pin (1) Retainer Spring (3) Tubing End Caps 4 BAG OF PARTS CONTENTS (continued) GROUP "D" (2) Latch Hook Assembly LOWER CHUTE ASSEMBLY TO MOWER DECK (2) Screw #10 x 5/8 (2) Washer, Lock #10 (2) Washer 3/16 x 3/4 x 16 Ga. (2) Nut, Weld #10 GROUP "E" CHUTE LATCH ASSEMBLY TO UPPER CHUTE (1) Screw #10 x 1-1/8 (2) Washer 3/16 x 3/4 x 16 Ga. (1) Spacer, Split #10 (1) Nut, Acorn #10 GROUP "F " CHUTE LATCH ASSEMBLY TO LOWER CHUTE (1) Rubber Latch (1) Screw #10 x 5/8 (1) Washer, Lock #10 (1) Washer 3/16 x 3/4 x 16 Ga. (1) Nut, Weld #10 5 ASSEMBLY PARTS IDENTIFICATION COVER UPPER CHUTE DUMP BAG INDICATOR r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subjked crac r is ne ntai en d. Coe wh r. Re cont erlyiently ent prop qu em r is g fre plac aine k ba d re contChecmende less n. m un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. 3) Use Hardware - - GROUP "B" CAUTION: Container support is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. CARRIAGE BOLTS LANCED TABS TOWARD BOTTOM FIG. Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. Install the four bolts and locknuts as shown and tighten securely. SUPPORT POST LOCKNUTS 7 FIG. 3 ASSEMBLY 4 MOUNTING TO TRACTOR (See Fig. 4) Use Hardware - - GROUP "C" NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. Raise seat on tractor to allow assembly to be mounted. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. Line up holes in mounting bracket with holes in support post and insert bracket support pin. [. . . ] Store in a clean, dry place. BLADE CARE For best results mower blades must be kept sharp. · See BLADE CARE instructions in your tractor owner's manual. CAUTION: BEFORE PERFORMING ANY MAINTENANCE, SERVICE OR ADJUSTMENTS: · Depress clutch brake pedal fully and set parking brake. · Place gearshift/motion control lever in neutral (N) position. [. . . ]