User manual HUSQVARNA CARB II

[. . . ] Operator's manual (CARB II, EPA II) 326C 326L 326LX-SERIES 326LDX-SERIES Please read these instructions carefully and make sure you understand them before using the machine. English SYMBOL EXPLANATION Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. [. . . ] • Tighten the wing nut. Assembling and dismantling the two-part shaft (326LDX) Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling‘s locking plate on the upper section of the shaft. • Tighten the handle. Dismantling • Undo the handle (at least three turns). • Press the handle towards the coupling. • Carefully twist the lower section out of the lock. Assembling the loop handlebar (326L, 326LX, 326LDX) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • 326LX-series: Fit the nut, knob and bolt. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/ knob. • Hold both parts of the shaft and pull out the lower section from the coupling. Assembly of the trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. ! 12 – English WARNING!Under no circumstances may the cutting equipment be used without an approved guard fitted. See the chapter “Technical data”. If the wrong guard or a defective guard is fitted this can cause serious personal injury. ASSEMBLY Assembling the spray guard and trimmer head Superauto II (326L, 326LX, 326LDX) • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the drive disc (B) on the output axle. • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. • The trimmer head must be split to be fitted (see the diagram). Proceed as follows: • Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. Press apart the trimmer head using the fingers on the cover. [. . . ] speed, left/right handles, max: 91/98 91/97 91/97 2, 7/1, 5 3, 5/1, 7 4, 4/4, 8 5, 7/5, 7 1, 7/1, 5 2, 7/1, 8 3, 9/5, 2 7, 2/9, 8 1, 7/1, 5 2, 7/1, 8 3, 9/5, 2 7, 2/9, 8 Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max speed. Sound pressure at the user's ear and vibration on the handles are measured with all the machine's approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories 326L, 326LX, 326LDX: Thread blade shaft M10 Plastic knives Trimmer head Type Tricut ∅ 300 mm Trimmy H II 1" Trimmy Fix Trimmy Hit Trimmy Hit Pro Superauto II 1" Tricut ∅ 230 mm (R) Trimmy Hit VI (R) Trimmy Hit Junior (R) Trimmy Fix (R) Trimmy Hit VII (R) Cutting attachment guard Art No. 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 503 97 71-01 / 503 93 42-02 326C: Thread blade shaft 3/8 (R) Plastic knives Trimmer head 537 02 61-01 / 537 07 67-01 537 02 61-01 / 537 07 67-01 537 02 61-01 / 537 07 67-01 537 02 61-01 / 537 07 67-01 537 02 61-01 / 537 07 67-01 20 – English EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U. S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. [. . . ]