Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUSQVARNA CLEARING SAW. We hope that this HUSQVARNA CLEARING SAW user guide will be useful to you.
Lastmanuals help download the user guide HUSQVARNA CLEARING SAW.
Manual abstract: user guide HUSQVARNA CLEARING SAW
Detailed instructions for use are in the User's Guide.
[. . . ] Mixing ratio 1:50 ( If Husqvarna two-stroke oil is not available, and you must use another oil, be certain that it is a high quality air-cooled two-stroke engine oil. mixing ratio is increased to 1:25(40/0). In countries where no two-stroke oil is available, engine oil SAE 30 is recommended. Never use multi-grade oil (10W-30) or waste oil. [. . . ] Q C
Z
B
B
M
u
f
The muffler is designed in order to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special screen, called a âspark arresterâ. If your saw has this type of muffler, you should clean the screen at least once a week. This is done by removing the screen from the muffler and cleaning it with a wire brush. The screen must be replaced, if damaged. The saw will be overheated, if the screen is clogged. This results in damage on the cylinder and the piston. Never use a saw with a clogged or defective muffler. If your saw is equipped with a spark arrester screen it should not be removed!Do not make any unauthorized changes to your muffler. M
a
i a
n
t i a
e
n n
a
n t
Below you will find some general maintenance instructions, For further information please contact your service dealer. check that the harness is undamaged , . Check the blade guard for damage or cracks. change the guard in case of impacts or cracks. Q Check that the saw blade is properly centred, sharp, and without cracks, An off-centred blade induces heavy vibrations that may damage the saw. q Check that the blade nut is sufficiently tightened. QM sure that the blade transport guard is undamaged and that it can be securely fitted, . Check that nuts and screws are sufficiently tightened,
W m a e i n e t . Check the starter, especially cord and return spring, q Clean the exterior of the spark plug. Q Clean the cooling fins on the cylinder and check that the air intake at the starter is not clogged. Q Check that the angle gear is filled with grease up to 3/4. [. . . ] The engine must not be run in non-ventilated areas as there is a risk of carbon monoxide poisoning. When working with the clearing saw always carry it in its suspension. Do not use a clearing saw that is worm or damaged and thereby hazards the safety. q
q
q q q
q q
q q q q q
q
q
P
s
e
e
q
a
r
u
q q q q q q
Helmet. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA CLEARING SAW
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA CLEARING SAW will begin.
