User manual HUSQVARNA HCLTH130C

[. . . ] WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. SAFETY RULES • • • • • • • • • Stop the blade(s) when crossing gravel drives, walks, or roads. Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute. [. . . ] Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. • MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. SEE “CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL. • • • TO STOP ENGINE • To stop engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start. If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. • Follow the maintenance schedule in this manual. LUBRICATION CHART WHEEL ADJUSTER (ON EACH WHEEL) ➀ ➁ ENGINE OIL ➀ MULCHER DOOR HINGE PIN ➀ REAR DOOR HINGE BEFORE EACH USE 1. Check for loose fasteners. LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”). IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELFLUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. ➀ HANDLE BRACKET MOUNTING PINS ➀ SPRAY LUBRICANT 9 ➁ SEE “ENGINE” IN MAINTENANCE SECTION MAINTENANCE LAWN MOWER Always observe safety rules when performing maintenance. TIRES • • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. 3. Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft. Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. • The recommended tightening torque is 35-40 ft. lbs. IMPORTANT: BLADE BOLT IS HEAT TREATED. IF BOLT NEEDS REPLACING, REPLACE ONLY WITH APPROVED BOLT SHOWN IN THE REPAIR PARTS SECTION OF THIS MANUAL. BLADE ADAPTER BLADE LOCK WASHER KEY CRANKSHAFT KEYWAY DRIVE WHEELS Check front drive wheels each time before you mow to be sure they move freely. [. . . ] 34 36 37 38 39 40 41 43 44 45 46 47 48 49 50 57 58 59 60 61 62 63 64 65 66 69 96 97 98 99 --- PART NO. 532 40 25-72 532 18 41-93 874 78 05-12 819 11 22-06 532 19 85-41 532 19 09-39 532 19 23-25 532 19 89-10 532 40 89-89 532 40 47-63 532 19 40-37 532 40 67-12 532 85 10-74 532 85 02-63 532 85 10-84 532 12 51-62 532 75 06-34 532 18 55-82 532 17 57-35 532 19 30-00 532 17 56-50 873 80 04-00 532 18 55-76 532 19 74-80 532 08 83-48 532 18 27-48 532 19 79-91 532 19 71-62 532 18 22-27 532 18 22-28 532 40 47-64 532 41 09-12 DESCRIPTION Axle Arm Assembly, Rear, LH Bolt Thread Cutting Screw w/Sems 5/16-18 x 3/4 Washer Nut, Hex Mounting Bracket, Debris Shield Screw Debris Shield Kit, Lawn Mower Housing (Includes Key Numbers 10, 11, 12 and 45) Danger Decal Blade Adapter / Pulley Blade, 21" Hardened Washer Helical Washer 3/8-24 x 1-3/8 Grade 8 Hex Head Machine Screw 3/8-24 x 1-3/8 Grade 8 Upstop Bracket Screw Discharge Deflector Hinge Bracket Spring Hinge Rod Nut, Hex Mulcher Door O-Ring Washer, Flat 1/2 Grip, Foam Clip, Cable Belt Keeper Screw Nut, Hex Decal, Warning (not shown) Owner’s Manual, English / French 17 25 26 27 28 30 31 32 33 532 15 04-06 532 14 52-12 532 41 08-15 532 16 08-28 532 40 25-71 532 70 10-37 532 19 01-57 873 80 05-00 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty. ROTARY LAWN MOWER - - MODEL NUMBER 65021CHV (HCLTH130C) - PRODUCT NUMBER 961 43 00-19 18 ROTARY LAWN MOWER - - MODEL NUMBER 65021CHV (HCLTH130C) - PRODUCT NUMBER 961 43 00-19 KEY NO. [. . . ]