User manual HUSQVARNA HECTH130C

[. . . ] 1. 3 Symbols in the Operator’s Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 4 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5 6 7 8 2. Presentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. 1 Automower™, what’s what? [. . . ] INSTALLATION Joining the boundary wire If the boundary wire is not long enough and needs to be spliced: Use original solderless coupler. It is waterproof and gives a reliable electrical connection. To splice: Insert both cable ends in the coupler. Now press down the button on top of the connector fully. Use a pair of pliers or the like, as the button on the connector is difficult to press down by hand. IMPORTANT INFORMATION Twisted cables, or a screw terminal (chock-block), insulated with insulation tape is not a satisfactory splice. Soil moisture will cause the conductors to oxidize and after a while result in a broken circuit. 3012-535 3012-536 3. 5 Connecting the boundary wire Connect the boundary wire to the loop generator/charger: 1. Place the cable ends in the connector: • Open the connector. • Place the wire in the connector grip. 3012-284 2. Press the connector together using a pair of pliers. Press until you hear a click. 3012-264 24 - English 3. Cut 0. 4" - 0. 8" above respective connectors. 3012-265 4. Attach the connector to the contact pin on the loop generator/charger. 3012-771 3. 6 Checking the installation Check the loop signal by looking to see what indication the green LED on the loop generator/charger is giving. If the grass is long it is appropriate to let Automower start mowing at the MAX cutting height. Once the grass is shorter, you can gradually lower the cutting height. Press the STOP button to stop the mower. Open the cutting height adjustment cover: Press down the catch button and then open the cover. 3012-776 3012-777 28 - English 4. The selected position is the marking on the knob that aligns with the arrow on the body. • Turn clockwise to raise the cutting height. • Turn anticlockwise to lower the cutting height. 3012-253 4. Close the cover. Ensure that the catch button locks. English - 29 4. USE 4. 6 Changing the PIN code To change the PIN code on the mower: 1. Connect the loop generator/charger charging cable to the mower's charger contact. At most the mower may be two metres from the working area's boundary wire and the loop generator/charger must be connected to the mains supply. [. . . ] 24 Link to Automower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Winter storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Chassis, Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Check the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]