User manual HUSQVARNA HELT151C

[. . . ] This manual contains proprietary information that is protected by copyright. No part of this manual may be photocopied, reproduced, or translated to another language without the written consent of Husqvarna. The information contained in this document is subject to change without notice. Husqvarna reserves the right to change specifications and designs at any time without notice and without the obligation of making changes to units previously sold. [. . . ] To protect the engine, remove spark plug and pour 1/2 ounce (14. 2 mL) of SAE 10 weight oil into the engine through the spark plug hole. Rotate engine crankshaft by hand several times, then install the spark plug and tighten to 20 ft-lb (27 N·m). Adjust tires to recommended tire pressure. Perform semiannual periodic lubrication. See Periodic Lubrication Schedules on page 34. Thoroughly clean front body, rear body, seats, engine compartment, and underside of vehicle. Chock the wheels to prevent the vehicle from rolling. RETURNING THE STORED GASOLINE VEHICLE TO SERVICE 1. Restore fuel system to operation (Figure 32, Page 47). Connect battery cables, positive (+) cable first, and tighten terminals to 12 ft-lb (16 N·m). Completely open the fuel shut-off valve (Figure 17). A partially closed fuel shut-off valve (Figure 18) combined with the use of the choke can result in a fouled spark plug and engine failure. • To avoid unintentionally starting the vehicle, before servicing always disconnect the battery, negative (–) cable first (Figure 1, Page 11) and disconnect the spark plug wire from the spark plug. • Frame ground – Do not allow tools or other metal objects to contact frame when disconnecting batteries or other electrical wiring. Never allow a positive wire to touch the vehicle frame, engine, or other metal component. Page 30 2007 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual Periodic Service Schedules PERIODIC SERVICE SCHEDULES See General Warnings on page 9. ý WARNING • Service, repairs, and adjustments must be made per instructions in the maintenance and service manual. NOTE: If the vehicle is constantly subjected to heavy use or severe operating conditions, the preventive maintenance procedure should be performed more often than recommended in the periodic service and lubrication schedules. Both the Periodic Service Schedule and Periodic Lubrication Schedule must be followed to keep vehicle in optimum operating condition. 2007 Husqvarna 4210-G, 4210-E, 4210-GXP, and 4210-EXP Owner’s Manual Page 31 Periodic Service Schedules PERIODIC SERVICE SCHEDULE – ELECTRIC VEHICLES REGULAR INTERVAL Daily service by owner Weekly service by owner Monthly service by owner or trained technician SERVICE Batteries Batteries Batteries Charge batteries (after each use only). Wash battery tops and clean terminals with baking soda/water solution. Check air pressure and adjust if necessary. Wash battery compartment and underside of vehicle. Check brake shoes; replace if necessary. See Section 6 – Wheel Brake Assemblies in the appropriate maintenance and service manual. Brake system Lubricate brake slides per Lubrication Schedule. [. . . ] HUSQVARNA will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part. *HUSQVARNA, its authorized dealers, or a service agency approved by HUSQVARNA. ITEMS COVERED BY THIS WARRANTY: The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if HUSQVARNA demonstrates that the engine or equipment has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the direct cause of the need for repair or replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly operating, adjustment limiting device is still eligible for warranty coverage. The following emission warranty parts list are covered: SYSTEMS COVERED PARTS DESCRIPTION Fuel Metering Carburetor assembly, fuel injection pump, fuel injection nozzle, fuel regulator Exhaust Catalyst Air Induction Air filter housing, air filter*, crankcase breather tube Ignition Flywheel magneto, ignition pulse generator, ignition coil assembly, ignition control module, spark plug cap, spark plug* Positive Crankcase Ventilation (PCV) System PCV valve, oil filler cap Misc. [. . . ]