User manual HUSQVARNA PRUNING SAW

[. . . ] Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. Be sure the area is clear of other people before mowing. Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. [. . . ] 12 Unlock drain valve by pushing inward and turning counterclockwise. After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. Refill engine with oil through oil fill dipstick tube. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick. TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 • • CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e FIG. 11 NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. IMPORTANT: Petroleum solvents, such as kerosene, are not to be used to clean the cartridge. They may cause deterioration of the cartridge. Do not use pressurized air to clean cartridge. 16 MAINTENANCE HANDLE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of use, whichever comes first. Spark plug type and gap setting is shown in "PRODUCT SPECIFICATIONS" section of this manual. IN-LINE FUEL FILTER (See Fig. 15) COVER CARTRIDGE PRE-CLEANER The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • With engine cool, remove filter and plug fuel line sections. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor. • Be sure there are no fuel line leaks and clamps are properly positioned. • Immediately wipe up any spilled gasoline. CLAMP CLAMP BASE 02698 TABS SLOTS 00667 FUEL FILTER FIG. 15 ENGINE OIL FILTER Replace the engine oil filter every season or every other oil change if the tractor is used more than 100 hours in one year. CLEANING • Clean engine, battery, seat, finish, etc. [. . . ] Deck - Order separately gauge wheel components key nos. 116-119) 11 --13 14 15 16 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 36 37 40 44 45 46 532 13 41-49 532 13 97-75 532 13 89-71 532 13 76-45 532 12 87-74 532 11 04-85 532 17 44-93 872 14 05-05 532 13 28-27 532 15 97-70 873 68 05-00 532 17 75-63 532 10 53-04 532 12 37-13 532 11 04-52 532 17 18-59 819 11 10-16 532 13 14-91 532 17 39-84 532 18 76-90 532 15 35-35 532 17 83-42 872 11 06-12 532 13 14-94 819 13 13-16 873 90 06-00 532 14 00-88 532 12 47-88 532 13 77-29 NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 41 WARRANTY STATEMENT SECTION 4: EXCEPTIONS AND LIMITATIONS SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held product. 3 Year Warranty: Spindles (on Zero Turn Riders and Commercial Walk-Behinds) 2 Year COMMERCIAL-Warranty: Husqvarna Commercial Turf Equipment—zero turn riders, wide area walks, and ground engaging commercial equipment. This warranty shall be inapplicable to defects resulting from the following: (1)Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; (2)Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna; (3)Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or: (4)Additional damage to parts or components due to continued use occurring after any of the above. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. [. . . ]