User manual HUSQVARNA ST 724

[. . . ] ST724 1. 1996 Spare Parts Piéces Dètachées Owner's Manual 601 00 17-36 Reference No. 337209 05/09/95 SAFETY RULES ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO PREVENT ACCIDENTAL STARTING WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR SNOW THROWER IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY CIRCUMSTANCES. BEFORE USE q Read the Owner’s Manual carefully. [. . . ] DO NOT ATTEMPT TO REMOVE ANY ITEM THAT MAY BECOME LODGED IN AUGER WITHOUT TAKING THE FOLLOWING PRECAUTIONS: q RELEASE AUGER DRIVE AND TRACTION DRIVE LEVERS. q DO NOT PLACE YOUR HANDS IN THE AUGER OR DISCHARGE CHUTE. USE A PRY BAR. SNOW THROWING TIPS q For maximum snow thrower efficiency in removing snow, adjust ground speed, NEVER the throttle. Go slower in deep, freezing or wet snow. If the unit slips, reduce forward speed. The engine is designed to deliver maximum performance at full throttle and should be run at this power setting at all times. Most efficient snow blowing is accomplished when the snow is removed immediately after it falls. For complete snow removal, slightly overlap each path previously taken. The snow should be discharged down wind whenever possible. For normal usage, set the skids so that the scraper bar is 1/8" above the skids. For extremely hardpacked snow surfaces, adjust the skids upward so that the scraper bar touches the ground. On gravel or crushed rock surfaces, set the skids at 1-1/4" below the scraper bar (see To Adjust Skid Height paragraph in the Service & Adjustments section of this manual). Rocks and gravel must not be picked up and thrown by the machine. After the snow blowing job has been completed, allow the engine to idle for a few minutes, which will melt snow and accumulated ice off the engine. Clean the snow thrower thoroughly after each use. Remove ice and snow accumulation and all debris from the entire snow thrower, and flush with water (if possible) to remove all salt or other chemicals. Wipe snow thrower dry. FROZEN STARTER If the starter is frozen and will not turn engine: q q Pull as much rope out of the starter as possible. Release the starter handle and let it snap back against the starter. q q q q If the engine still fails to start, push the primer button two or three times again and repeat the two previous steps until the engine starts. Then continue with the directions for cold start. To help prevent possible freeze-up of recoil starter and engine controls, proceed as follows after each snow removal job. q With the engine running, pull the starter rope hard with a continuous full arm stroke three or four times. Pulling of starter rope will produce a loud clattering sound. [. . . ] SKID, HEIGHT ADJUST BOLT, 5/16-18X. 75 CARR. FLATWASHER . 344X. 69X. 065 WASHER, HVSPTLK . 31X. 58X. 08 NUT, 5/16-18 REGHEX 334396C 34 24" SNOW THROWER MODEL ST 724 DISCHARGE CHUTE REPAIR PARTS 584 594 586 598 597 593 602 603 610 609 608 606 593 595 596 582 590 591 585 600 587 586 580 601 611 REF. NO 580 582 584 585 586 587 590 591 593 594 595 596 597 PART NO. 601 00 18-36 601 00 13-91 601 00 14-64 601 00 13-91 601 00 15-24 601 00 14-64 601 00 08-99 601 00 06-54 601 00 15-24 601 00 00-19 601 00 00-23 601 00 00-19 601 00 06-84 PART NAME CHUTE, UPPER SCREW, 5/16-18X. 75 SLTRMA NUT, 5/16-18 HEXNYL SCREW, 5/16-18X. 75 WASHER, PLASTIC . 315X. 75X. 064 NUT, 5/16-18 HEXNYL BOLT, 5/16-18X1. 00 CARR. [. . . ]