User manual HUSQVARNA TC-TXC

[. . . ] ENGLISH 1 PRESENTATION Welcome to the Husqvarna motorcycling Family!Your new Husqvarna motorcycle is designed and manufactured to be the finest in its field. The instructions in this book have been prepared to provide a simple and understandable guide for your motorcycle's operation and care. Follow the instructions carefully to obtain maximum performance and your personal motorcycling pleasure. [. . . ] For the adjusting proceed as follows: - loosen the screw (1); - turn the cam (2) in order to adjust the brake pedal idle stroke (A);- the operation done, tighten the screw (1). The adjusting operation carried out, adjust the idle stroke of the pedal as indicated in page 43. REAR BRAKE IDLE STROKE ADJUSTMENT The rear brake foot pedal should have a (B) 5 mm (0. 2 in. ) idle stroke before starting the true braking action. Should this not happen as follows: - loosen nut (3); - operate the pump rod (4) to increase or decrease the idle - tighten nut (3) at the end of the operation. WARNING When the idle stroke figures are not met, the brake pads will be subjected to a fast wear that may bring to the TOTAL BRAKE INEFFECTIVENESS. stroke; 42 CHECKING THE FLUID LEVEL The level (A) must be set between the pump tank notches. ADJUSTMENT OF THE CONTROL LEVER AND CHECK OF THE HYDRAULIC CLUTCH FLUID LEVEL Free play (A) must be at least 3 mm (0. 1 in. ). The lever position can be adjusted for any driver hand size. To decrease the lever distance from the handle grip, rotate the adjuster (B) CLOCKWISE. To increase the lever distance from the handle grip, rotate the adjuster (B) COUNTERCLOCKWISE. To check the fluid level, proceed as follows: - remove screws (1), cover (2) and rubber pump diaphragm on the handlebar clutch control; - by keeping the master cylinder (3) in horizontal position, check the fluid level is NOT BELOW 4 mm (0. 16 in. ) from the upper surface (D) of the pump body; - if necessary, add fluid until the correct level is reached see TABLE FOR LUBRICATION-SUPPLIES for the fluid type page 12. CAUTION*: NEVER use brake fluid. Reassembly the removed parts using the reverse procedure. Periodically check the connecting hose (see "Periodical maintenance card"): if the hose (C) show is bent or cracked, its replacement is advised. EN TC-TXC 43 HYDRAULIC CLUTCH BLEEDING Proceed as follows: - remove screws (1), cap (2) and rubber pump diaphragm; - remove the bleeding nipple (3); - mount a syringe in the bleeding nipple hole, then refill with fresh fluid see LUBRICATION TABLE on page 12. - refill until fluid is discharged from the lower hole (B) on the pump body WITHOUT BUBBLES. The fluid level MUST NEVER BE below 4 mm from the top (A) of the clutch pump body (see picture). Reassemble the removed parts. 44 ADJUSTING THE SUSPENSIONS ACCORDING TO PARTICULAR TRACK CONDITIONS The following information is a useful guide for setting up the suspensions according to the road conditions. Always start from the standard calibration before making any change on the suspensions. Afterwards, increase or decrease the adjusting clicks one at a time. HARD GROUND Fork: softer compression adjustment. Shock absorber: softer compression adjustment. The softer adjustment for the two suspensions is also used both in compression and in extension when driving at top speed, in order to have better grip of the tires. SANDY GROUND Fork: have a harder compression adjustment, or replace the standard spring with a harder one, and make a softer compression adjustment and a harder extension adjustment at the same time. Shock absorber: have a harder compression, and expecially a harder extension adjustment. Work on the spring preload to lower the motorcycle rear side. MUDDY GROUND Fork: have a harder compression adjustment, or replace the standard spring with a harder one. Shock absorber: have a harder compression and extension adjustments, or replace the standard spring with a harder one. [. . . ] THE BUYER FURTHER ACKNOWLEDGES THAT THIS MOTORCYCLE IS NOT INTENDED FOR USE ON PUBLIC STREETS, ROADS, HIGHWAYS, OR TRAILS UNDER PUBLIC JURISDICTION AND THAT USE ON SUCH MAY VIOLATE STATE AND FEDERAL LAW. Noise emission warranty MV Agusta Motor S. p. A. warrants that this exhaust system, at the time of sale, meets all applicable U. S. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers. Warranty claims should be addressed to Cagiva U. S. A. [. . . ]