User manual HUSQVARNA YTH2348

[. . . ] YTH2348 Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 43 08-90 Rev. 3 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. [. . . ] Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. OIL DRAIN VALVE CLOSED AND LOCKED POSITION YELLOW CAP 02 46 3 DRAIN TUBE TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. • • ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 CLEAN AIR SCREEN Fig. 15 Refill engine with oil through oil fill dipstick tube. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Use gauge on oil fill cap/dipstick for checking level. Insert dipstick into the tube and rest the oil fill cap on the tube. Do not thread the cap onto the tube when taking reading. Keep oil at “FULL line on dipstick. ” Tighten cap onto the tube securely when finished. Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. AIR FILTER TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE oil_visc_chart1_e Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. 14 NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. 14 and 15) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. [. . . ] Mower Rear Bolt Shoulder Bolt Carr Sqnk 7/16-24 x 2 Screw TT #10-32. 5 3/8 Flange Port, Washout Coupling Quick Connect Mandrel Assembly (Includes housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) 532 43 18-25 Replacement Mower, Complete NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 41 TRACTOR - - MODEL NO. YTH2348 SEAT ASSEMBLY (96045002500), PRODUCT NO. 960 45 00-25 1 8 8 7 8 41 40 7 8 10 21 6 37 37 2 44 43 21 3 seat-tex_6. 5SL_2 KEY NO. [. . . ]