User manual HUSQVARNA YTH24V42LS

[. . . ] 07002 YTH24V42LS Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine. " 532 44 04-29 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. BLADE REMOVAL (See Fig. 14) • Raise mower to highest position to allow access to blades. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. • Remove blade bolt by turning counterclockwise. • Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY. • Install and tighten blade bolt securely (45-55 Ft. torque). MANDREL ASSEMBLY BLADE IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED. BLADE BOLT (SPECIAL) STAR CENTER HOLE Fig. 14 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Rinse the battery with plain water and dry. • Clean terminals and battery cable ends with wire brush until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 13 15 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. LOWER DASH COVER TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. [. . . ] inches 1 inch = 25. 4 mm wheel_art_1-tex 39 TRACTOR - MODEL NO. 960 43 01-28 MOWER DECK 52 25 27 34 30 50 56 28 29 47 24 26 35 32 37 38 251 24 54 53 55 34 18 10 8 41 40 48 3 4 5 51 23 22 19 46 31 24 25 42 44 45 14 49 33 59 36 9 1 13 12 43 60 21 58 2 6 20 17 16 11 7 42_F_elec-Tex_3 15 40 TRACTOR - MODEL NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO. 575 43 80-01 539 11 21-70 539 10 75-20 539 10 76-30 539 10 75-90 539 11 20-78 539 19 30-03 532 17 60-66 532 17 91-27 539 19 42-08 532 11 07-31 532 11 07-35 532 11 07-36 532 19 51-61 539 11 24-12 539 99 07-99 539 99 07-17 575 22 45-01 539 13 27-28 539 10 82-71 539 10 65-04 539 99 05-17 539 97 69-79 539 11 28-99 539 10 48-64 532 17 85-15 532 19 61-04 574 82 71-02 539 99 09-23 532 17 79-68 539 10 47-63 539 99 06-92 DESCRIPTION Deck w/Decals 42" Housing Assembly Washer-Spacer Screw, Washer Head Nut, 9/16 Top Center Lock Blade, 14-5/8" Bolt, 7/16, Assy Blade Roller, Nose Rod, Roller, Nose Clip Retainer Discharge Chute - 42” Plastic Spring - Torsion Pin, Clevis 5/16 x 5. 19 Stud, Fasten w/ Anti- Rotate Confinement Plate Rhsnb 5/16-18 x 5/8 Gr. [. . . ]