User manual I-TECH BLUETOOTH VIRTUAL KEYBOARD FOR WINDOWS MOBILE 5

[. . . ] 11 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Short-Cuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2 Introduction Congratulations on choosing the VKB Virtual Keyboard for Pocket PC. The keyboard will allow the effortless composition of documents and e-mails and will turn your PDA into a truly indispensable tool whether in the office or on the go. [. . . ] Take a few moments to familiarize yourself with device using the diagram below. Overview 1. 6. Figure 1 ­ Getting to know your Virtual Keyboard Keyboard projection window Keyboard sensing receiver window Reset Button On/Off Button Charging Socket Status indicator (LED) 5 Before using your Virtual Keyboard: · Ensure that you remove all protection materials including the protection sheet on the laser windows. Your Virtual Keyboard will need to be charged for at least 2 hours. · Switching On Place the Virtual Keyboard on a flat surface with the Keyboard projection and sensing windows facing you. To switch it on press the On/Off button, located on the upper-left hand side. Once the unit is switched on an image of a keyboard is projected on to the surface. Notice that the keyboard image is the basic English keyboard, including 4 Arrow keys, 1 Control, 2 Shift keys, 1 Alt and a VKB dedicated Fn function key. A two-color LED located at the top of the unit indicates the current status of the Virtual Keyboard, where: Colour Blinking Blue Long Flash Blue Blinking Red Solid Red Status/Cause Virtual Keyboard is ready to pair to a Bluetooth device Virtual Keyboard is paired to a Bluetooth device Virtual Keyboard's battery is low. Recharge the Virtual Keyboard Action The area of the Move the Virtual projected keyboard is Keyboard to a exposed to direct shaded location sun-shine or some other source of direct light. Table 1 ­ Functional Status Indicator 6 Virtual Keyboard your Pocket PC and Bluetooth The Virtual Keyboard (VKB) is equipped with Bluetooth, a short-ranged radio communications technology which allows the device to communicate with your Pocket PC up to 10 meters away without the need for a physical connection. As with all Bluetooth devices, to connect with your Pocket PC you will need to do the following: Pair/bond your Pocket PC device to the virtual keyboard. . . . . . and connect. Preparing your keyboard for pairing Place the Virtual keyboard on a flat surface and turn it on. The blue LED at the top should flash at about once a second. This signifies that the Virtual Keyboard is currently "unpaired" with any device. If this is not the case, please see "Resetting the keyboard to factory settings" or "Preparing the keyboard to be paired with a different device" on page 10. Your keyboard is now ready for pairing. Pairing/Bonding with your device 1) Ensure Bluetooth is turned On. 7 2) Go to the Bluetooth Settings program. 3) Tap the Devices button and then New Partnership. 4) Tap the VKB Keyboard icon. 5) Using the keyboard on the screen of the Pocket PC device, enter a passkey of between 1 and 8 digits and then tap OK 6) Listen for the "beep" on the Virtual Keyboard, then, using the keyboard projected by the Virtual Keyboard repeat the passkey and press return [ ]. 7) From the services available for the VKB Keyboard, select Input Device. The keyboard will "beep" and you may now type. 8 Virtual Keyboard Features Projection Intensity You may adjust the intensity of the projected keyboard to your liking, selecting between a low, medium and high setting. Press Shift-Fn-UpArrow to increase the intensity and Shift-Fn-DownArrow to decrease the intensity. Sensitivity As part of the Virtual Keyboard's detection a Sensitivity setting is employed. You may need to adjust this for optimal use. If you are experiencing missing keys, try increasing the sensitivity. [. . . ] Pick up the keyboard and wait for it to turn off, Place the Virtual Keyboard back on the flat surface and turn it on. The Virtual Keyboard is now ready for pairing. · · · · Preparing the keyboard to be paired with a different device Once the keyboard has been paired and connected to a host device, to pair the keyboard with a different host device, turn the keyboard on, and on the projected image press the keys +Fn+B simultaneously for 3 seconds. The keyboard will emit a short beep and the LED will flash blue to indicate it is ready for pairing with another device. 10 Troubleshooting Problem My keyboard is connected, but little or no keys are being detected When typing, multiple and/or erroneous keys are displayed in addition to those I have pressed. Device is not resting on a firm flat surface Reposition device to a firm surface. [. . . ]