User manual ICOM 2200H

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER i2200H This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-2200H VHF TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] c Push [SCAN 2(T-SCAN)] to start the scan. Y Z · Push [Y] or [Z] for 1 sec. also starts the scan. 7 w Set the squelch to the point where noise is just muted. to start the scan. · To change the scanning direction, rotate [DIAL]. · The memory channel readout blinks the scan type as follows: v Push [SET B(D-OFF)] to switch full and programmed scan (P1, P2 and P3). b To stop the scan push [SCAN 2(T-SCAN)] or [CLR A(MW)]. r Push [SET LOCK ] to switch full and programmed scan (P1, P2 and P3). t To stop the scan, push [SET LOCK ] or [V/MHz SCAN ]. · During full scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During programmed scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During memory scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During Bank scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz ( SET ) to select full, Push band* (A1, AA) or programmed scan (P1, P2 and P3) in sequence. (*Depends on versions) A1 : FM band (136­174 MHz) AA : AM band (118­136 MHz) LOCK Indicates scan edge channels. · P1 stands for 1A/1b · P1 to P3 are available when they are programmed, and ( SET ) . switches with LOCK When AM and FM frequencies are programmed into memory channel disorderly, memory scan takes a lot of time (very slow). In this case, assign AM and FM frequencies into the separate bank respectively. And using the bank scan is helpful. 38 7 SCAN OPERATION I Scan edges programming Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 1A/1b to 3A/3b, in memory channels. q Set the edge frequency of the desired frequency range in VFO mode: Set the frequency using [DIAL]. w Push [S. MW MW ] momentarily. · "M" indicator and channel number blink. r Push [S. MW MW ] for 1 sec. to program. · 3 beeps sound and VFO is automatically selected. · Scan edge 1b, 2b or 3b is automatically selected when continuing to push [S. MW MW ] after programming. t To program a frequency for the other pair of scan edges, 1b, 2b or 3b, repeat steps q and r. · If the same frequency is programmed into a pair of scan edges, programmed scan will not function. e Rotate [DIAL] to select one of scan edge channel, 1A, 2A or 3A. [EXAMPLE]: Programming 145. 300 MHz into scan edges 1A. Push MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN () SCAN S. MW MW V/ MHz Rotate DIGITAL PRIO AO BUSY for setting frequency, etc. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push MUTE NAR MID LOW LOCK momentarily. DIGITAL PRIO AO BUSY ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz S. MW MW Rotate DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push for 1 sec. and continue to push MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN DIGITAL PRIO AO BUSY SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz " "Beep " Beep " Beep " DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz 39 SCAN OPERATION D Programming scan edges via microphone MW 7 z Set the desired frequency in VFO mode. YZ Set the frequency via the keypad or [Y]/[Z]. x Push [FUNC] then [CLR A(MW)] momentarily. Y Z c Push [Y] or [Z] to select scan edge channels, 1A, 2A or 3A. v Push [FUNC], then push [CLR A(MW)] for 1 sec. [. . . ] 9) DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN LOCK SET T-SCAN SET MONI LOW TONE M/CALL V/MHz TONE SCAN V/MHz PRIO SCAN SCAN M/CALL V/MHz V/ MHz BANK OPT When the DTMF memory encoder is activated. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN DIGITAL PRIO AO BUSY MUTE NAR MID LOW DTMF MEMORY DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz PRIO LOCK ANM DUP T-SCAN PRIO SCAN M/CALL SET MONI LOW TONE M/CALL V/ MHz MEMORY MODE (p. 35) DIGITAL PRIO AO BUSY SET MONI LOW TONE M/CALL V/ MHz See p. 45 for details. ANM MONI MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz CLONE MODE DIGITAL PRIO AO BUSY MUTE NAR MID LOW for 1 sec. WEATHER CHANNEL (p. 83)*2 BANK OPT ANM LOCK ANM DUP T-SCAN PRIO SCAN MONI DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN MONI LOW TONE M/CALL V/ MHz See p. [. . . ]