User manual ICOM CS-F3 PROGRAMMING MANUAL

[. . . ] 2­3 2-2 TREE VIEW SCREEN DESCRIPTION . 6­22 3-1 KEY & DISPLAY ASSIGN . 22 12 PROGRAMMING for LTR® TRUNKING operation . 63 13 DATA CLONING BETWEEN TRANSCEIVERS . [. . . ] When [Priority A (Rewrite)] switch is assigned, priority channel A can be re-assigned by pushing [Priority A (Rewrite)] switch for 1 sec. B: Priority-- "B" tagged channel becomes the priority channel B, simply recalled by pushing [Priority B] switch. E: Emergency-- "E" tagged channel becomes an emergency channel, immediately recalled and sends an emergency signal by pushing [Emergency Single] or [Emergency Repeat] switch, or when the man down function is activated. SmarTrunk ON/OFF-- Specifies the selected bank for SmarTrunk operation. Go to Prio A (Rewrite) Go to Emergency Single, Emergency Repeat Go to Man Down-- ON, Timer The channel attribution can only be set on the Memory channel Screen as shown above. (Cannot be set in the Edit window. ) However, the other items are programmable in the Edit window only. The Edit window appears by pushing the [Enter] key, double clicking or selecting in the sub menu window via right click operation with the mouse on the desired channel. 29 5 SCREEN MENU OPERATION-- PMR · Frequency-- RX, TX Enter receive and transmit frequencies within the following frequency ranges in either 5, 6. 25 or 7. 5 kHz steps* for the RX and TX boxes, respectively. IC-F31GT/GS : 136­174 MHz IC-F41GT/GS : 400­430, 440­480, 470­500, 490­520 MHz *according to version · Frequency-- Text Enter up to a 12-character text in the Text box for memory name, channel usage, etc. The usable characters are A­Z, a­z, 0­9, $, ', (, ), ­, /, <, =, >, @, [, \, ], _, {, |, } ~ and user original characters. When no text is entered, the channel number is indicated. When entering user original characters, enter `%' and the desired thumbnail number A to P (capital letter only). When no receive frequency is entered, other items cannot be programmed in the channel. When SmarTrunk ON/OFF is selected for the editing bank in CH Atr (p. In A+R1, In A+R2: In addition to the `In_A' condition as above, a reset code 1 or 2 is automatically transmitted when call transmission is performed or 5-tone mute is activated by pushing [Moni(Audi)] switch. Both : Mutes the 5-tones when `SGL' is selected in CH Mute (p. 38) in this screen by pushing [Moni(Audi)] switch. Releases 5-tone mute when `SGL' is selected in CH Mute (p. 38) in this screen by pushing [Moni(Audi)] switch for 1 sec. Releases all mute controls and emits audio while pushing and holding [Moni(Audi)] switch. 32 SCREEN MENU OPERATION-- PMR 5 · SW Action-- Moni (continued) Both+R1, Both+R2: In addition to the `Both' condition as above, a reset code 1 or 2 is automatically transmitted when call transmission is performed via [Call] switch or 5-tone mute is activated by pushing [Moni(Audi)] switch. The [Moni(Audi)] and [Call] switches are assigned in the 3-1 KEY & DISPLAY ASSIGN (pgs. The reset code 1 and 2 are programmed in 10-2 TX CODE CHANNEL (p. 52), and channels 32 (reset code 1) and 31 (reset code 2) are used, respectively. The mute condition will be returned to initial condition when the Auto Reset timer is activated, specified in Auto Reset in this screen (p. Go to CH Mute Go to Moni(Audi) Go to Call Go to 10-2 TX CODE CHANNEL Go to Auto Reset · SW Action-- Sel Selects the mute condition after memory or TX code channel selection from OFF, Aud and In A. OFF : Does not change even when selecting memory or TX code channel. Aud : Releases the 5-tone mute when `SGL' is selected in CH Mute (p. [. . . ] e Unscrew 2 screws d, then remove multi-connector. r Unscrew 2 screws e then separate the chassis from the front panel in the direction of the arrow. Be careful!: A flat cable is connected between the MAIN unit on the chassis and front panel. NOTE: When installing UT-105 or UT-111, the unit MUST BE plugged into SLOT 1. [. . . ]