User manual ICOM IC-02AT

[. . . ] We want to take a couple of moments of your time to thank you for making your IC-V82/U82 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-V82/U82. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-V82/U82. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES 7 W*-- high transmit output power (*IC-V82, 5 W for IC-U82) CTCSS and DTCS encoder/decoder standard Optional digital modulator/demodulator Optional DTMF decoder Icom, Icom Inc. [. . . ] Push A FUNC OPT 0 w Push and hold [0·OPT] for 1 sec. to select the DTMF memory. Push Appears OPT 0 for 1 sec. · 4th page indication · 5th page indication e Rotate [VOL] to select the desired memory. r Push [MONI] or [PTT] to exit the DTMF memory mode. · Selected DTMF code sequence sounds when [MONI] is pushed. Appears Blinks tWhile pushing [PTT], push [MONI] to transmit the selected DTMF memory. · After the DTMF code sequence is transmitted, the transceiver returns to receive automatically. 28 DTMF MEMORY 7 DTMF transmission rate D Manual DTMF code transmission While pushing [PTT], push digit keys, [A·FUNC], [B·CALL], [C·MR], [D·CLR], [#·BANK] and [·ENT ] to transmit a DTMF code sequence manually. · [·ENT ] transmits tone "E", [#·BANK] transmits tone "F. " USING INITIAL SET MODE When slow DTMF transmission rates are required with DTMF memory transmission (as for some repeaters), the transceiver's rate of DTMF transmission can be adjusted. Y qWhile pushing and holding [Y] and Z [Z], turn the power ON to enter INITIAL SET MODE. [VOL] 7 A FUNC B CALL C MR D CLR TONE 1 P. BEEP 2 T. SCAN 3 BANK DUP 4 SCAN 5 SKIP 6 OPT 0 Y Z wPush [Y] or [Z] several times until "dtd" appears. eRotate [VOL] to select the desired DTMF transmission rate. · Four rates are available: "1" (100 msec. intervals) is the fastest; "5" (500 msec. intervals) is the slowest. PWR PRIO 7 SET 8 H/M/L 9 ENT ENT rPush [·ENT ] to exit INITIAL SET MODE. 29 8 Band edge SCAN OPERATION Programmed scan End 1b 2b 3b Scan types PROGRAMMED SCAN Start 1A 2A 3A Scan edges Scan Jump Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies. Band edge Programmed scan repeatedly scans between two user programmed frequencies (memory channels "1A­3A" and "1b­3b") or scans between upper and lower band edges. This scan is useful for checking for signals within a specific frequency range such as repeater output frequencies, etc. Scans between lower (start) and high (stop) frequency. q Push [D·CLR] to select VFO mode, if necessary. wPush [A·FUNC] and [5·SCAN] to start the scan, then a selected scan edge appears as "P1, " "P2, " "P3" or "AL. " · To change the scan edge, push [A·FUNC] and [8·SET] several times until the desired scan edge appears. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition. VFO frequency Mch 3 Mch 2 Mch 1 When a signal is received during scanning, the scan resume condition determines what action the transceiver takes. The transceiver has 2 scan resume conditions available as illustrated below. Use SET MODE to select the one which best suits your needs. q Push [A·FUNC], then push [8·SET] to enter SET MODE. Y Z wPush [Y] or [Z] several times until "SCP" or "SCt" appears. e Rotate [VOL] to select the desired scan resume condition. · Pause scan: When receiving a signal, scan pauses on the signal until it disappears. · Timer scan: When receiving a signal, scan pauses on the signal for 5 sec. , 10 sec. or 15 sec. , then resumes. 8 Memory scan Priority channel Mch 4 Mch 5 Mch 6 Pause scan 5 sec. Mch 199 SKIP 50 msec. r Push [D·CLR] to stop the watching. Timer scan r Push [·ENT ] (or [D·CLR]) to set and exit SET MODE. 33 9 SUBAUDIBLE TONES Tone squelch D Operation The tone squelch opens only when receiving a signal containing a matching subaudible tone. You can wait for calls from group members using the same tone and not hear other signals. q Set the operating frequency. · Set the volume and squelch to the desired level as the normal operation. NOTE: The transceiver has 50 tone frequencies and consequently their spacing is narrow compared to units having 38 tones. Therefore, some tone frequencies may receive interference from adjacent tone frequencies. [. . . ] 64) · Battery protection function (p. 68) : Push : Push · S-meter squelch (p. 68) *Available for [USA]/[CSA] versions only. Appears only when an optional UT-118 DIGITAL UNIT is installed. · DTMF rate (p. [. . . ]