User manual ICOM IC-2330A

[. . . ] NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention-- anything less may result in an accident. [. . . ] The transceiver has two inhibiting conditions, repeater and busy. Push [SET] one or more times until the "RPt" display appears as shown below. X 1 5 9 1 5 9 Push [PWR] to turn power OFF. While pushing [SET] (far left switch), turn power ON to enter initial set mode. Push [SET] one or more times until the "RLO" display apAuto repeater function is turned OFF Auto repeater function is ON, tone encoder is OFF pears as shown below. X Rotate the tuning dial to turn the auto repeater function to "R1, " "R2" or OFF. · "R1": auto repeater is ON, tone encoder is OFF. · "R2": auto repeater is ON, tone encoder is ON. Repeater lockout function is turned OFF Transmit is inhibited when the tone squelch is closed Push [PWR] to exit initial set mode. Rotate the tuning dial to turn the repeater lockout function to "RP, " "BU" or OFF. · "RP": Transmit is inhibited when the tone squelch is closed. · "BU": Transmit is inhibited when a signal is received. Push [PWR] to exit initial set mode. 25 6 MEMORY OPERATION s Memory channel selection D Using the tuning dial Push [M/CALL] once or twice to display "!". Rotate the tuning dial to select the desired memory channel. · Only programmed memory channels can be selected. s General description The transceiver has 107 memory channels including 6 scan edge memory channels (3 pairs), and 1 call channel. In addition, 6 scratch pad memories are available (see p. Each of these channels can be individually programmed with the following data. 13) · Duplex direction and offset (pgs. 21, 24) · Subaudible tone encoder or tone squelch and its tone frequency (pgs. 40\) *Except for scan edge memory channels. D Using the [Y]/[Z] keys MR Ä Push [MR] to select memory mode. to transfer. MW FUNC + CLR A Select the memory channel to be programmed. Select memory mode by pushing [M/CALL] once or twice ("!" appears). Rotate the tuning dial to select the memory channel. Push [S. MW] momentarily, then rotate the tuning dial to select another memory channel to transfer. · To transfer to the VFO, push and hold [(S. MW)MW] instead of pushing momentarily. Push and hold [(S. MW)MW] to transfer when a momentary push was used in the previous step. 29 6 MEMORY OPERATION s Memory clearing Contents of programmed memories can be cleared (blanked), if desired. NOTE: Be careful--the contents of cleared memories CANNOT be recalled. Push [S. MW] momentarily. Select the memory channel to be cleared with the tuning dial. Push [S. MW] briefly, then a second time for 1 sec. · 3 beeps sound, then the frequency is cleared. · "!" flashes continuously. · Scan edges 1A/1b and the call channel cannot be cleared. Push any switch to stop the flashing. [EXAMPLE]: Clearing memory channel 20. Push X 1 5 9 1 S. MW MW momentarily X Rotate 5 9 1 5 9 M M Push S. MW MW S. MW MW briefly, then push again for 1 sec. 1 5 9 Push any switch 1 5 9 M 30 MEMORY OPERATION 6 s Alphanumeric display Each memory channel and the call channel can be programmed with an alphanumeric name such as a repeater name, club name, etc. , for easy recognition. Names can be a maximum of 6 characters--see the table below for available characters. NOTE: Scan edge channels and scratch pad memories CANNOT be programmed with alphanumeric names. 1 A J T / 2 B K U = 3 C L V _ 4 D M W < 5 D N X > 6 E O Y ( 7 F P Z ) 8 G Q + , 9 H R ­ : 10 I S M space Push [(MONI)ANM] for 2 sec. to select alphanumeric indication. · "NONAME" appears when a name has not yet been programmed into the channel. Push [SET] to enter programming mode. · The first character of the name flashes. Rotate the tuning dial to select the desired character. · See the table at left for a list of available characters. Push [SET] to advance to the next character. · Push [MONI] to select the previous character. Push [V/MHz] to program the name and exit programming mode. Push [(SET)ANM] for 2 sec. [. . . ] audio 1. 0 A : SO-239 (50 ) : ­10°C to +60°C; ­14°F to +140°F : 140(W) × 40(H) × 180(D) mm 51/2(W) × 19/16(H) × 73/32(D) in : 1. 2 kg; 2 lb 10 oz : Double-conversion superheterodyne : 1st 15. 65 MHz 2nd 450 kHz : Less than 0. 18 µV : Less than 0. 13 µV : More than 12 kHz/­6 dB Less than 28 kHz/­60 dB (6 kHz/­6 dB, 18 kHz/­60 dB; FM narrow mode) · Spurious response rejection ratio : More than 60 dB · Audio output power : More than 2. 4 W at 10% (at 13. 8 V DC) distortion with an 8 load · Ext. speaker connector : 2-conductor 3. 5 (d) mm (1/8") /8 63 17 OPTIONS D Wireless remote accessories HM-90 WIRELESS MICROPHONE Infrared, full remote control microphone. EX-1759 INFRARED RECEIVER Used to receive control signals from the HM-90. EX-1513 INFRARED SUB RECEIVER Used with the EX-1759 to increase remote control reliability and extend the controllable area. Some of the following options may not be available due to variations in local electrical standards, etc. [. . . ]