User manual ICOM IC-260 SCHEMATIC

[. . . ] This radio has been tested and complies with the FCC RF exposure limits for "Occupational Use Only". In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: · FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. · American National Standards Institute (C95. 1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. · American National Standards Institute (C95. 3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields­ RF and Microwave. [. . . ] BANK-TYPE: Push [Bank], then push [ ] or [ ] to select the desired bank. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 11 12 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 I Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. 15, 16 for selection. I Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. 1 for antenna attachment. 3 Receiving: q Rotate [VOL] to turn power ON. e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. · When a tone signalling system is used, the call procedure described at left may be necessary. w Push the call switch (assigned to one of the dealer programmable switches: [P0], [P1], [P2], [P3], [Red], [ ] and [ ]). e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling w Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your signal; 1. The editable digit will move to the right automatically. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the selected TX code. 16 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. TO SELECT A TX CODE: q Push [DTMF Autodial]-- a DTMF channel appears. w Push [ ]/[ ] to select the desired DTMF channel. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. I User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can "customize" transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [ ] and [ ], rotate [VOL] to enter the user set mode at power ON. w Push and hold [P0] to enter user set mode. Push [P0] momentarily to select the item. Then push [ ] and [ ] to set the desired level/condition. [. . . ] The following are additionally required. · An AC adapter (BC-124) or the DC power cable (OPC-656) IC-260/F60 BP-227 5 AC adapter (Purchase separately. ) AD-100 charger adapters are installed in each slot. AD-100 charger adapter is installed in BC-119N. MUL ER HARG TI-C Optional OPC-515L (for 13. 8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter. DC power cable (OPC-656) (Connect with the DC power supply; 13. 8 V/at least 7 A) 41 42 5 BATTERY CHARGING BATTERY CHARGING 5 I Optional battery case When using the optional battery case attached to the transceiver, install 5 × AA (R6) size alkaline batteries as illustrated at right. The BP-226 meets JIS waterproof specification grade 4. q Hook your finger under the latch, and open the cover in the direction of the arrow (q). [. . . ]