User manual ICOM IC-2710H

[. . . ] INSTRUCTION MANUAL DUAL BAND FM TRANSCEIVER iC- 2710h IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL--This instruction manual contains important operating instructions for the IC-2710H. CAUTIONS RWARNING!NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. [. . . ] Ç Push [Y] or [Z] several times to select the desired memory channel. · Pushing [Y]/[Z] more than 0. 5 sec. · If a scan is activated, push [Y] or [Z] again to stop it. D Using the keypad MR ENT Ä Push [BAND] to select the desired band, if necessary. Å Push [MR] to select memory mode. Ç Push [GENT] to activate the keypad for numeral input. É Push 2 appropriate digit keys to input a channel number. · When inputting non-programmed channel numbers the previous memory channel appears. · To select scan edge channels, "B" and "A" can be used for A and b respectively. C 32 6 MEMORY OPERATION I Programming a memory channel VFO mode settings, including the set mode contents such as subaudible tone frequency, etc. , are programmed into a memory channel. to program. · Memory channels not yet programmed are blank. · Memory channel number automatically advances when continuing to push [S. MW] after programming. Set the desired frequency in VFO mode: Push [S. MW] momentarily. Push the desired band's [V/MHz] to select VFO mode. Set the frequency using the desired band's tuning dial. · "!" and the memory channel number flashes. Rotate the tuning dial to select the memory channel to be CONVENIENT Memory programming can be performed in versatile ways e. g. memory channel to the same (or different) memory channel, memory channel to the call channel, etc. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 via the remote controller. Push and V/MHz SCAN Rotate for setting freq. , etc. Push S. MW MW momentarily 1 5 9 1 5 9 1 5 9 Rotate Push S. MW MW for 1 sec. and continue pushing 33 MEMORY OPERATION 6 I Programming a memory channel via the microphone MW Memory channel programming can be performed via the microphone. Ç Push [FUNC] then [EMW] momentarily. É Select the memory channel to be programmed: Push [Y] or [Z] to select the memory channel (direct numeral input cannot be used). Ä Push [BAND] to select the desired band, if necessary. Å Set the desired frequency in VFO mode: Push [VFO] to select VFO mode. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if required. Ñ Push [FUNC] then [EMW] for 1 sec. to program. 3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc. ) are programmed. Memory channel number advances when continuing to push [MW] after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 via the microphone. Push BAND , MONI VFO 1 8 HIGH 4 7 MID 5 MW ENT C DUP+ DUP Push FUNC then CLR A momentarily 1 5 9 1 5 9 1 5 9 MW Push Push FUNC then CLR A for 1 sec. and continue pushing 34 6 MEMORY OPERATION I Transferring memory contents This function transfers a memory channel's contents into a VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency, etc. Push DUP ­ T Ä Push [BAND] to select the desired band, if necMW essary. Å Select the memory channel to be transferred: Push [MR] to select memory mode. Push [Y] or [Z] to select the memory channel; or push [GENT] then push the desired memory channel number (2 digits) to select the memory channel directly. S. MW MW for 1 sec. DUP ­ T Ç Push [FUNC] then [EMW] momentarily, then push [Y] or [Z] to select another memory channel to transfer. · To transfer to the VFO, push [FUNC] then push and hold [EMW] instead of pushing momentarily. MW FUNC + CLR A É Push [FUNC] then [EMW] for 1 sec. to transfer when a momentary push was used in the previous step. Push the desired band's tuning dial. Select the memory channel to be transferred: Select memory mode by pushing the selected band's [M/CALL] once or twice ("!" appears). [. . . ] Frequency range: 144­148 MHz and 430­450 MHz. input power: 150 W AHB-32 TRUNK MOUNT Trunk mount with a coaxial cable for the AH-32. D Speakers SP-7 EXTERNAL SPEAKER For base station use. Cable length: 1. 0 m; 3. 3 ft SP-10 EXTERNAL SPEAKER Compact design. Cable length: 1. 5 m; 4. 9 ft SP-12 EXTERNAL SPEAKER Slim-type. [. . . ]