User manual ICOM IC-475H

[. . . ] This device emits Radio Frequency (RF) energy. Extreme caution should be observed when operating this device. If you have any questions regarding RF exposure and safety standards please refer to the Federal Communications Commission Office of Engineering and Technology's report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electromagnetic Fields (OET Bulletin 65). NEVER attach an antenna or internal antenna connector during transmission. [. . . ] to enter the noise blanker set mode. · Auto notch filter (p. 50) While "S4" is selected, push [(F-1)ANF] to turn the auto notch filter function ON and OFF. · "ANF" appears when the noise reduction is set to ON. · AGC (auto gain control) (p. 48) While "M4" is selected, push [(F-3)AGC] to select AGC fast and AGC slow. · Push [DISPLAY] once or twice to select M. · Push [MENU] one or more times to select M4. · "FAGC" appears when the fast time constant is selected. · 1/4 function While "M4" is selected, push [(F-1)1/4] to turn the 1/4 function ON and OFF. · Push [DISPLAY] once or twice to select M. · Push [MENU] one or more times to select M4. 4 D Convenient functions for transmit · Break-in function (p. 32) While "M4" is selected, push [(F-2)KEY] for 1 sec. to enter the keyer set mode. · Push [DISPLAY] once or twice to select M. · Push [MENU] one or more times to select M4. Rotate the main dial to select the break-in OFF, semi break-in or full break-in. · "BK" or "F-BK" appears when the semi break-in or full break-in is set to ON, respectively. D CW reverse mode QUICK SET MODE The CWå (CW Reverse) mode receives CW signals with a reverse side CW carrier point like that of LSB and USB modes. Use this mode when interference signals are near the desired signal and you want to change the interference tone. e Push [MENU] one or more times to select "Q3 CW REV, " then rotate the main dial to select CW and CWå modes. · Check the interference tone. CW pitch is adjustable from 300 to 900 Hz in 10 Hz steps. CW The default is 600 Hz. K4 CW PADDLE This item adjusts the CW paddle type. ·n : normal (for electronic keyer use) ·r : reverse (for electronic keyer use) · buG : When using the electronic keyer, key down produces a "dash, " releasing the key automatically produces a "dot(s). " · oFF : Turns OFF the electronic keyer (for straight key use) · ud : For using the microphone's [UP]/[DN] keys instead of the CW paddle. CW The default is "n, " normal. K5 RATIO This item adjusts the CW key ratio (or weight). The ratio can be selected from 2. 8 to 4. 5. CW The default is 3. 0. 32 4 RECEIVE AND TRANSMIT I Memory keyer functions The transceiver has a number of convenient functions for the electronic keyer that can be accessed from the memory keyer menu. to select the memory keyer send menu. · Push [MODE] momentarily to return to normal CW operating mode. [MODE] e Push [DISPLAY] to enter the memory keyer menu. See the diagram below. · Push [DISPLAY] momentarily to return to the memory keyer send menu. [DISPLAY] · CW mode CW MODE · Memory keyer send menu CW DISPLAY · Memory keyer menu CW Push BLANK S1 3 5 7 9 35 20 40 60dB BLANK S1 3 5 7 9 35 20 40 60dB Push VFO A CH VFO A CH M4 1/4 KEY AGC Push for 1 sec. PO 1 1. 5 2 10 MODE -1 MK1 MK2 MK3 Push MENU F1 F2 F3 PO 1 1. 5 2 10 DISPLAY Ä EDT 001 SET MENU F1 F2 F3 Push [F-1] Push [F-2] Push [F-3] Push [MENU](Ä) or [DIAPLAY] Push [DISPLAY] Push [DISPLAY] · Edit menu CW · Contest number set mode CW CW · Menory keyer set mode CW CW CW Ä MK1 MK2 MK3 MENU F1 F2 F3 01 NUM STYLE 02 CNT UP TRIG MENU 03 PRESENT No. Push* 01 REPEAT TIME 02 MSG DISPLAY MENU Push* *Set mode item can be selected with [Y BAND]/[Z BAND] or [M-CH] during set mode. Push Push Push Push [MENU](Ä) or [DIAPLAY] CW CW Push [MENU](Ä) or [DIAPLAY] CW Push [MENU](Ä) or [DIAPLAY] Ä ÅCQ TEST CÇ _ MENU F1 F2 F3 Ä ÅUR 5NN* BÇ _ MENU F1 F2 F3 Ä ÅCFU TU _ MENU F1 F2 F3 Ç 33 RECEIVE AND TRANSMIT 4 D Memory keyer send menu Pre-set characters can be sent using the memory keyer send menu. Contents of the memory keyer are set using the edit menu. · Transmitting q Select CW mode with [MODE]. 32). · When step r is performed during the break-in function OFF, monitors the memory keyer contents. [MODE] [F-1] [F-3] [MENU] [F-2] · Memory keyer send menu CW r Push one of the function keys ([(F-1)MK1] to [(F-3)MK3]) to send the contents of the memory keyer. · Pushing a function key for 1 sec. [. . . ] Indication 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 PEAK HOLD QUICK SPLIT SPLIT LOCK SPL OFFSET SCAN RESUME SCAN SPEED U/D SPEED AM NB PAD CH PWR ON CHK A-TUNE STRT PTT TUNE TUNER SW 9600 MODE SPEECH LANG SPEECH SPD S-LVL SPCH CI-V CI-V CI-V CI-V ADDRES BAUD TRN 731 Description Peak meter hold setting Quick split function Split lock function Split offset frequency Scan resume condition Scanning speed [UP]/[DN] speed Noise blanker in AM mode Available memo pads Power ON check function Auto tune start function PTT tune function Tuner switch condition Packet data speed Voice synthesizer lang. Voice synthesizer speed S-meter level speech CI-V address setting Data transfer rate CI-V transceive CI-V data length Initial set mode No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 MENU Y Z *When "3 SIMPLE MODE" is set to ON, box items are undisplayed. 93 MENU GUIDE 18 S1 M1 M2 MENU MW SCN MPW PRI SEL 14 NR MPR V/M (in memory mode) SPL MW FIL VOX 1/4 1/4 1/4 VOX A/B MCL NB COM KEY TON XFC DISPLAY MENU S2 V/M S3 7 ANF MET AGC (SSB/AM) AGC (CW) AGC (RTTY) AGC (SSB-D) DISPLAY MENU 21 NRL M3 M4 M4 M4 MODE S4 DISPLAY G1 G2 G3 G4 BAND scope SWR Graph TX freq. Memory name M4 M4 COM TON (FM) DISPLAY DISPLAY For 1 sec. Quick set mode Y No. [. . . ]