User manual ICOM IC-756PROII

[. . . ] INSTRUCTION MANUAL HF/50 MHz ALL MODE TRANSCEIVER i756PROTM This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. EXPLICIT DEFINITIONS WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk or personal injury, fire or electric shock. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the IC-756PROII. PRECAUTIONS R WARNING HIGH VOLTAGE! [. . . ] · Receive sensitivity is insufficient during low gain, or while using a narrow band antenna (such as small loop, a Beverage antenna or a short Yagi antenna, etc. ) is used. 37 5 RECEIVE AND TRANSMIT I Digital voice recorder The transceiver has a total of 8 memory channels, 4 each for transmit and receive, of digital voice memories. can be recorded in each receive channel, and a total message length of 90 sec. Providing a transmission memory is very convenient for repeated CQ and number transmissions at contest times, as well as when making consecutive calls in DX'pedition. · Recording a received audio q Push [EXIT/SET] several times to close a multifunction screen, if necessary. w Select the desired mode by pushing [SSB], [CW/RTTY] or [AM/FM]. e Push [(F-2)VOICE] to call up the voice recorder screen. · If the transmit voice memory channel (T1­T4) appears, push [(F-5)T/R] to select receive voice memory channel. AGC MID VOX OFF COMP OFF WIDE R1 VOICE RECORDER R1 R1 R2 R2 R3 R3 R4 R4 RX M E M O R Y · Playing the recorded audio q Push [EXIT/SET] several times to close a multifunction screen, if necessary. w Push [(F-2)VOICE] to call up the voice recorder screen. · If the transmit voice memory channel (T1­T4) appears, push [(F-5)T/R] to select receive voice memory channel. AGC MID VOX OFF VOICE RECORDER R1 R1 R2 R2 R3 R3 R4 R4 14. 100. 00 14. 100. 00 USB USB 15:30 15:30 8 s 8s ------------- 14. 100. 00 14. 100. 00 USB USB 15:30 15:30 8 s 8s ------------- COMP OFF WIDE R1 RX M E M O R Y R2 R3 R4 T/R R2 R3 R4 T/R e Push the desired memory channel switch, [(F-1)R1] ­ [(F-4)R4], momentarily to playback. · "PLAY" appears. AGC MID VOX OFF COMP OFF WIDE R1 VOICE RECORDER PLAY r Push the desired memory channel switch, [(F-1)R1] ­ [(F-4)R4], for 1 sec. to start recording. · "REC" flashes and the recording timer counts up. · The operating frequency, mode and current time are programmed as the memory names automatically. · Previously recorded contents are cleared. AGC MID VOX OFF COMP OFF WIDE R1 VOICE RECORDER REC R1 R1 R2 R2 R3 R3 R4 R4 14. 195. 00 14. 195. 00 USB USB 10:10 10:10 5 s 5s ------------- RX M E M O R Y R2 R3 R4 T/R R1 R1 R2 R2 R3 R3 R4 R4 14. 195. 00 14. 195. 00 USB USB 10:10 10:10 10s 10s ------------- RX M E M O R Y r Push the selected memory channel switch, [(F-1)R1] ­ [(F-4)R4], again to stop playback if desired. · Playback is terminated automatically when all of the recorded contents in the channel are played, or after 15 sec. R2 R3 R4 T/R t Push the selected memory channel switch, [(F-1)R1] ­ [(F-4)R4], again to stop recording. · Recording is automatically terminated after 30 min. t Push [EXIT/SET] twice to exit the voice memory screen. IMPORTANT!Push one of [(F-1)R1]­[(F-4)R4] to stop recording before, or when 15 sec. The voice recorder memory records the 15 sec. (max. ) of audio before one of [(F-1)R1]­[(F4)R4] is pushed. audio will be over-recorded with the last 5 sec. , so that the total of audio recorded is 15 sec. y Push [EXIT/SET] twice to exit the voice memory screen. 38 RECEIVE AND TRANSMIT 5 I Digital voice recorder (continued) · One-touch voice recording To record the receiving signal contents immediately, one-touch voice recording is available. while receiving a signal to start recording. · "REC" flashes. · Records audio into the channel R4. [REC/PLAY] switch w Push [REC/PLAY] momentarily to stop recording. · Recording is automatically terminated after 30 min. IMPORTANT!Push [REC/PLAY] to stop recording before, or when 15 sec. has passed from the start of recording. ANT 1 BW 2. 4k SFT 0 USB FIL2 qw:pp TX TX METER Po P. AMP 1 ATT OFF VFO qr. qot. pp 1 14. 100. 00 USB VFO USB FIL2 qr. wpt. pp 1 14. 100. 00 USB REC · One-touch playback The recorded audio in the channel R4 can be playback without selecting the voice memory screen. q Push [REC/PLAY] to playback. · "PLAY" appears. · Playback the recorded audio in the channel R4. AGC MID VOX OFF COMP OFF WIDE SCOPE VOICE MEMORY SCAN w Push [REC/PLAY] again to stop playback if desired. · Playback is terminated automatically when all of the recorded contents in the channel R4 are played, or after 15 sec. 39 5 RECEIVE AND TRANSMIT I Digital voice recorder (continued) · Recording a message for transmit To transmit a message using a voice recorder, record the desired message in advance as described below. q Push [EXIT/SET] several times to close a multifunction screen, if necessary. w Push [(F-2)VOICE] to call up the voice recorder screen. AGC MID VOX OFF MIC REC R EC r Push the desired memory channel switch, [(F-1)T1] ­ [(F-4)T4], momentarily to start playback and confirmation. AGC MID VOX OFF COMP OFF WIDE T1 VOICE MIC-RECORD PLAY T1 T1 T2 T2 T3 T3 T4 T4 0 50 100 % 10s 10s ------------Remain 80s REC LEVEL T2 T3 T4 NAME VOICE RECORDER VOICE RECORDER MENU R EC OR DE R ME NU PLAY PLA Y TX Variable 4ch (Total 90s) V ar ia bl e 4c h (T ot a l 9 0 s ) RX 15s Endless 4ch (TOT 30m) R X 15 s En dl es s 4 ch ( T O T 3 0 m ) Mic Record/Record check M ic R ec or d/ Re co rd c he c k Recorder Output Adjust R ec or de r Ou tp ut A dj us t Auto Monitor SET Au to M on it or S ET TX LEV. [. . . ] input power: 5 W Designed for base station operation. · Input impedance: 8 · Max. input power: 5 W For remote transceiver control using a personal computer. You can change frequencies, operating mode, memory channels, etc. ·About DC power supply The use of IC-756PROII (#23, #24, #25, #28, #30) in combination with the DC power supply complies with European Harmonised Standard regulations under the conditions listed below. Conditions ·In combination with PS-125 ·About IC-PW1 LINEAR AMPLIFIER The IC-PW1 LINEAR AMPLIFIER does not comply with European Harmonised Standard regulations. [. . . ]