User manual ICOM IC-A210E

[. . . ] INSTRUCTION MANUAL VHF AIR BAND TRANSCEIVER iA210E IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. FEATURES Large, bright OLED display A fixed mount VHF airband first!The IC-A210E has an organic light emitting diode (OLED) display. All man-made lighting emits its own light and display offers many advantages in brightness, not brightness, vividness, high contrast, wide viewing angle and response time compared to a conventional display. In addition, the auto dimmer function adjusts the display for optimum brightness at day or night. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-A210E. Easy channel selection EXPLICIT DEFINITIONS The explicit definitions below apply to this instruction manual. [. . . ] Revive the previous memory channel data. Do nothing and return to the memory mode. r Rotate [DIAL] to select the desired channel. t Push [MEM], rotate [O-DIAL] to select a menu as follow. · The memory channel number blinks. t Push [MEM] to perform the selected action. REPLACE DELETE REVIVE GRP NAME CH TAG DONE Replace to the standby frequency. Revive the previous memory channel data. Set the memory channel as a tag channel. Do nothing and return to the memory mode. 13 y Push [MEM] to perform the selected action. 3 MEMORY OPERATION I History memory channel The transceiver has 10 history memory channels. The standby frequency is stored into a history memory channel when pushing []. The frequency is stored into the history memory channel in order from "CH01" to "CH10. " q Push [RCL] to enter the memory mode. · The channel number appears. · The memory channel name also appears if it has been entered. I Clearing the memory contents (Regular and group memory channels only) Unwanted memory channels can be cleared. q Push [RCL] to select memory mode. · The channel number appears. · The memory channel name also appears if it has been entered. w Rotate [O-DIAL] to select the memory channel type. · Select from regular memory channel or group memory channel. w Rotate [O-DIAL] to select the history memory channel. · "HISTORY" appears. RX HISTORY e Rotate [DIAL] to select the desired channel. r Push [MEM], then rotate [O-DIAL] to select "DELETE. " · The memory channel number blinks. RX MEMORY 122. 00 127. 005 CH01 122. 00 127. 000 ÅDELETE CH01 Ç 127. 000 e Rotate [DIAL] to select the desired channel. · Push [] to exchange the history memory channel frequency to the active frequency if necessary. t Push [MEM] to delete the memory channel data. · "-- -- -- -- -- --" appears momentarily, then the next selectable channel appears. RX MEMORY r Push [RCL] to exit the memory mode. 122. 00 CH01 y Push [RCL] to exit the memory mode. NOTE: Instead of steps r and t, pushing and holding [MEM] for 2 sec. after step e also allows delete or revive operation. 14 MEMORY OPERATION 3 I Programming channel names (Regular memory channel only) The regular memory channel can display a 6-character name in addition to the memory number. q Push [RCL], then rotate [O-DIAL] to select the regular memory channel in the memory mode. w Rotate [DIAL] to select the desired channel. e Push [MEM], then rotate [O-DIAL] to select "CH NAME. " r Push [MEM], then memory channel name's 1st digit blinks. t Rotate [DIAL] to select the desired character. · The character type as shown below is selectable. · Push [DIAL] to switch capital (A, B, C, ···) lower case (A, B, C, ···) number (0, 1, 2, ···) capital (A, B, C, ···) in order. I Programming group names (Group memory channel only) The group memory channel can display a 6-character name in addition to the group number ("GRP01"­"GRP20"). q Push [RCL], then rotate [O-DIAL] to select the desired memory channel in the memory mode. · Rotate [O-DIAL] to select the memory channel type if necessary. 03 w Push [DIAL], and then rotate [O-DIAL] to select the memory group from GRP01 to GRP20, if necessary. · Push [DIAL] again to decide the memory group. e Push [MEM], then rotate [O-DIAL] to select "GRP NAME". r Push [MEM], then group name's 1st digit blinks. t Rotate [DIAL] to select the desired character. · The character type as shown left "Selectable characters" is selectable. [. . . ] : Setting the frequency step to 8. 33 kHz. NOTE: When using an external speaker, the beep tone level when the squelch is closed is fixed and cannot be changed in the MENU mode. D Memory Clear "MEM CLEAR" Setting values in the CPU are cleared. Push and hold [MEM] for 2 sec. , the CPU is reset as follow. · MENU · MEMORY · ALL : MENU mode items are reset. : All CPU data is reset. D Intercom Usable Setting "INCOM MODE" Set the intercom using or not. · ON · OFF : The intercom is usable. : The intercom is unusable. 25 6 INSTALLATION AND REMOVAL t Turn the wrench clockwise until the main unit is fixed to the installation rack. · Turn the wrench in the upper socket as shown below when using the installation rack for Icom products. [. . . ]