User manual ICOM IC-F14

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF14/S UHF TRANSCEIVER iF24/S This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference. SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as "Occupational Use Only", meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazW ARN ING ards. This radio is NOT intended for use by the "General Population" in an uncontrolled environment. [. . . ] u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. 9) i ANTENNA CONNECTOR Connects the supplied antenna. q CHANNEL SW/SELECTOR · IC-F14S/F24S: Toggle the channel switch to select the pre-programmed channel 1 or 2. · IC-F14/F24 : Rotate the channel selector to select the preprogrammed memory channels. w VOLUME CONTROL [VOL] Rotate to turn the power ON/OFF and adjust the audio level. 6 D Programmable key reference Upper Lower 7 2 PANEL DESCRIPTION PANEL DESCRIPTION 2 2 ` LED indicator The LED indicator indicates several information as follows; (Ref. ; R=Red, G=Green, O=Orange) ` Programmable function keys The following functions can be assigned to [Upper] and [Lower] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. · Push to un-mute the channel (sets to `Audible' only). · Push after the communication is finished to send a `reset code'. DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code. · Call transmission is necessary before you call another station depending on your signalling system. · [Call A] and/or [Call B] keys may be available when your system employs selective `Individual/Group' calls. Ask your dealer which call is assigned to each key. NOTE: The un-mute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible` condition) after a specified period. LOCK KEY Push and hold to electronically lock all programmable keys except the following: [Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys. OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, depending on the pre-setting. · Ask your dealer for the output power level for each selection. EMERGENCY KEYS Push and hold to transmit an emergency call. When [Emergency Single (Silent)] or [Emergency Repeat (Silent)] is pushed, an emergency call is transmitted without a beep emission. · If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. · The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. VOICE SCRAMBLER FUNCTION KEYS Push to turn the voice scrambler function OFF. Push and hold to turn the voice scrambler function ON. OPT OUT KEYS Push to inactivate the connected output signal level. Push and hold to activate the connected output signal level. This function can be used for situations other than an emergency alert such as a security alarm for example. TALK AROUND KEY Push to turn the talk around function OFF. Push and hold to turn the talk around function ON. · The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to select the IF bandwidth to wide. · The wide passband width can be selected from 25. 0 or 20. 0 kHz using the CS-F14 CLONING SOFTWARE. (PMR operation only) Ask your dealer for details. Push and hold to select the IF bandwidth to narrow. 10 11 3 CONVENTIONAL OPERATION I Call procedure [VOL] CONVENTIONAL OPERATION 3 I Turning power ON Rotate [VOL] to turn power ON. When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. [. . . ] w Release the battery pack if it is attached. 3) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w 6 CAUTION: HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 28 29 7 OPTIONS D BELT CLIPS OPTIONS 7 D BATTERY PACK · BP-230 Li-Ion BATTERY PACK 7. 4 V/800 mAh Li-Ion battery pack, allows approx. · BP-231 Li-Ion BATTERY PACK 7. 4 V/1150 mAh Li-Ion battery pack, allows approx. [. . . ]