User manual ICOM IC-F1500

[. . . ] This connection will ruin the transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. EXPLICIT DEFINITIONS The following explicit definitions apply to this manual. DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. [. . . ] 13 s SmarTrunk IITM operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . only CAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc. , could void your authority to operate this transceiver under FCC regulations. 5 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ii 1 PANEL DESCRIPTION s Front panel VOLUME CONTROL FUNCTION DISPLAY PROGRAMMABLE FUNCTION KEYS SPEAKER P0 P1 P2 P3 MICROPHONE CONNECTOR PROGRAMMABLE FUNCTION KEYS POWER SWITCH 1 PANEL DESCRIPTION VOLUME CONTROL Adjusts the audio output level. · Minimum audio level (when setting control at maximum counterclockwise) is pre-programmed. POWER SWITCH Turns the power ON and OFF. · The following functions are available at power ON as options: · Automatic scan start · Password prompt 1 s Programmable function keys The following functions can be assigned to programmable function keys. Assigned function names can be affixed to the LCD using supplied stickers. CHANNEL UP AND DOWN KEYS · Select an operating channel CH UP · Select a bank after pushing the [BANK S] key. CH DN · Select a DTMF channel after pushing the [DTMF] key. · Select a scan group after pushing and holding the [SCAN] key. BANK UP AND DOWN KEYS Select a bank (a group of 16 (or multiples of) chanBK UP nels). BK DN MICROPHONE CONNECTOR Connects the supplied microphone or optional DTMF microphone for SmarTrunk IITM operation here. · The audio output level is linked to the transceiver's volume control. 4 1 PANEL DESCRIPTION s Function display BUSY INDICATOR Appears while the channel is busy. BELL INDICATOR Appears or blinks when the optional 2-tone call is received. TRANSMIT INDICATOR Appears while transmitting. AUDIBLE INDICATOR Appears when monitor function is turned OFF (CTCSS and DTCS mutes are released). BANK NUMBER READOUT Appears for the `Bank' type and 180 channel type only. Shows the selected bank number or a hundred digit to show more than 100 channels. ACTIVATED KEY INDICATOR Appears or blinks when the key under this indicator is activated. 5 OPERATION s Turning power ON I q Push [K ] to turn the power ON. 2 s Channel selection There are several types are available, and channel selection method may differ according to your system: Opening message may differ depending on the pre-setting. · A power-up alert tone sounds for about 1 sec. and an opening message may appears. w If the transceiver is programmed for start up passcode, input digit codes as directed by your system operator. NON-BANK TYPE: Push the [CH UP] or [CH DN] keys to select the desired operating channel, in sequence; or, push one of the [CH 1] to [CH 4] keys to select these channels directly. BANK-TYPE: q Push [BK S], then push [CH UP] or [CH DN] to select the desired bank number; or Bank number Push [BK UP] or [BK DN] if the transceiver has these keys. w Push [CH UP] or [CH DN] to select the desired channel in the selected bank. · The following keys can be used for this display appears. the password input: · The transceiver detects the numbers in the same block as the same number. Therefore the same effect for "1234" and "6789. " Input your password if KEY NUMBER P0 P1 P2 P3 0 5 1 6 2 7 3 8 4 9 e When the "PASSWORD" indication does not clear after 4digit input, the input code number may be incorrect. Turn power off and start over in this case. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or taking the microphone off from the microphone hanger. 6 2 OPERATION D Transmitting notes · Transmit inhibit function The transceiver has several lockout/inhibit functions which restricts the transmission under the following conditions: · Channel is busy. [. . . ] NOTE: The sponge supplied with the UT-105 is for the IC-F30/F40 series transceivers only. 12 4 OPTIONAL SmarTrunk IITM OPERATION s SmarTrunk IITM operation These features are enabled by a dealer or system operator and may not be available in your system. Contact your dealer for details. s SmarTrunk IITM and conventional modes This transceiver meets to SmarTrunk IITM functions. The optional UT-105 allows communication in conventional channels or SmarTrunk IITM channels. Select a channel bank for SmarTrunk IITM before trunking operation. [. . . ]