User manual ICOM IC-F310 IC-F320 IC-F410 IC-F420

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF310 iF320 UHF TRANSCEIVER iF410 iF420 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. CAUTIONS RWARNING!NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. [. . . ] · Select a transmit code channel after pushing the [TX CH] key. · Select a DTMF channel after pushing the [DTMF] key. · Select a scan group after pushing and holding the [SCAN] key. CH 1 CH 2 CH 3 CH 4 OPERATING CHANNEL KEYS Select an operating channel directly. SCAN TAG KEY Adds or deletes the selected channel to the scan group. BEEP Push to turn the beep tones ON/OFF. BEEP 3 PANEL DESCRIPTION LOCK KEY Electronically locks all programmable keys except the following: · [CALL] (incl. CAL A and CAL B), [MONI] and [EMER] keys. MONITOR KEY Activates one of (or two of) the following functions on each channel independently: · Push and hold the key to unmute the channel (audio is emitted; `Audible' condition). · Push the key to toggle the mute and unmute conditions (toggles `Audible' and `Inaudible'). · Push the key to mute the channel (sets to `Inaudible' only). · Push the key to unmute the channel (sets to `Audible' only). · Push the key after the communication is finished to send a `reset code'. 1 LOCK HIGH LOW1 OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or permanently depending on the pre-setting. level for each selection. LOW2 · Ask your Dealer or System Operator for the output power MONI TA TALK AROUND KEY Turns the talk around function ON and OFF. · The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communication. CALL CAL A CAL B CALL KEYS Transmit a 5-tone call. · Call transmission is necessary before you call another station depending on your signaling system. · The [CAL A] and/or [CAL B] keys may be available when your system employs selective `Individual/Group' calls. Ask your System Operator which call is assigned to each key. NOTE: The unmute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible` condition) after a specified period. WIDE/NARROW KEY Push [W/N] to toggle bandwidth between wide or narrow. · This function is available for W/N versions only. EMER EMERGENCY KEY Push and hold the key to transmit an emergency call. · If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. · The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. W/N 4 1 PANEL DESCRIPTION TX CODE KEY Select a transmit 5-tone code (station code) channel. · Push and hold to changes the contents of the station code using [ ]/[ ] keys. · Push to selects a TX 5-tone code channel using [ ]/[ ] keys after pushing this key. TX CODE CHANNEL UP/DOWN KEY Push to selects a TX code channel directory. DTMF CHANNEL SELECT KEY Push this key to select a DTMF channel. · Push this key, then select the desired DTMF channel using the [ ]/[ ] keys. Push and hold this key to transmit the selected DTMF code. NOTE: DTMF channels 6 and 7 are used for ID code and emergency code respectively, depending on your system set up. [. . . ] Ask your Dealer about antennas and the best places to mount them. s Fuse replacement Two fuses are installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the problem, if possible, and replace the damaged fuse with a new, rated one. Fuse rating IC-F310/F410: 15 A, IC-F320/F420: 20 A OPTIONAL CABLE PIN ASSIGNMENT trewq q LCD backlit cont. GND s Cleaning If the transceiver becomes dusty or dirty, wipe it clean with a dry, soft cloth. AVOID the use of solvents such as benzene or alcohol, as they may damage transceiver surfaces. oiuy 12 4 OPTIONAL SmarTrunk IITM OPERATION s SmarTrunk IITM operation These features are enabled by a Dealer or System Operator and may not be available in your system. [. . . ]