User manual ICOM IC-F4062T-S

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF3062T/S iF4062T/S UHF TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] e Push [TX Code Enter] to select the desired digit to be edited. · The digit to be edited blinks. 3 D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. TO SELECT A TX CODE: q Push [DTMF Autodial]-- a DTMF channel appears. w Push [CH Up] or [CH Down] to select the desired DTMF channel. e Push [DTMF Autodial] to transmit the DTMF code in the selected DTMF channel. 3 r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. t Push [TX Code Enter] to set the digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to the right will blink automatically without pushing [TX Code CH Enter]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. *IC-F3062T/IC-F4062T (10-key type) only 15 3 BASIC OPERATION User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can "customize" the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [P1] and [P2], rotate [VOL] to turn the power ON. Then, push and hold [P0] to enter user set mode. w Push [P0] several times to select the appropriate item. Then push [Side2] or [Side3] to set the desired level/condition. · Available set mode functions are Backlight, LCD contrast, Beep, Beep Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, VOX Gain, VOX Delay, Battery Voltage and Signal Moni. Scrambler function The voice scrambler function provides private communication between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler function ON. · " " appears. w Push [Scrambler] again to turn the scrambler function OFF. · " " disappears. e Rotate [VOL] to turn the power OFF to exit user set mode. NOTE: User set mode is also available via a programmable key. 10)) [User Set Mode] section. 16 BIIS OPERATION Setting example The following functions are assigned to each programmable key for display example. However, the assigned function can be changed by your dealer. [P0]; Call : Push to transmit a 5-tone/BIIS call when the selected channel is a 5-tone or BIIS channel. C · "CALL" is displayed on the key indicator. 4 3 4 Receiving a call D Individual call q When an individual call is received; · Beeps sound. · " " appears and the mute is released. C · The programmed text message (e. g. "CALLING") and the calling station ID (or text) is displayed when the indication mode is 2 lines. C · The programmed text message (e. g. "CALLING") and the calling station ID (or text) is displayed alternately when the indication mode is 1 line, depending on the setting. · " " appears or blinks depending on the setting. [. . . ] ·BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. 36 D DC CABLES · CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) · OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13. 8 V power source instead of the AC adapter. [. . . ]