User manual ICOM IC-F44GT

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER UHF TRANSCEIVER iF34GT/GS iF44GT/GS IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTION R CAUTION!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F34GT/GS VHF TRANSCEIVER and IC-F44GT/GS UHF TRANSCEIVER. R CAUTION!NEVER operate the transceiver with a headset or other audio accessories at high volume levels. [. . . ] In this case you can "customize" the transceiver operation to suit your preferences and operating style. Entering the user set mode: q Push and hold [User Set Mode] to enter user set mode. Push [User Set Mode] momentarily to select the item. Then push [UP] or [DOWN] to set the desired level/condition. · Available set mode functions are Backlight, Beep, SQL Level, Mic Gain and Battery Voltage. w Push and hold [User Set Mode] to exit user set mode. I Scrambler function The voice scrambler function provides private communication between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler function ON. ·" " appears. w Push [Scrambler] again to turn the scrambler function OFF. ·" " disappears. 15 4 BIIS OPERATION I Receiving a call D Individual call q When an individual call is received; · Beeps sound. · " " appears and the mute is released. · The programmed text message (e. g. " ") and the calling station ID (or text) is displayed alternately, depending on the setting. · " " appears or blinks depending on the setting. I Default setting The following functions are assigned to each programmable key as the default. However, the assigned function can be changed by your dealer. NOTE: [TX Code Enter] must be assigned to any key. : Push to transmit a 5-tone/BIIS call when the selected channel is a 5tone or MSK channel, respectively. [P1]; Digital : Push to select the call list ID/transmit message, or to display the receive message record for selection. [P3]; TX Code Enter : Push to enter the direct ID code edit mode for both 5-tone and MSK. [UP]/[DOWN]; CH Up/Down : While in the standby condition, selects the operating channel. After pushing [Digital] or [TX Code CH Select], selects call list or TX code channel, respectively. [MONITOR]; Moni(Audi): Push this key after the communication to send a `Clear down' signal during MSK channel operation. [P2]/[RED]; Null : No function is assigned. [P0]; Call Appears Appears or blinks w Push and hold [PTT], then speak into the microphone at a normal voice level. ·" ·" " indicator appears. " appears while receiving a signal. e Release [PTT] to return to receive. r To finish the conversation, push [MONITOR] (Moni(Audi)) to send the `Clear down' signal. · Either station can send a `Clear down' signal. ·" " is displayed for 2 sec. [. . . ] *In addition to SmarTrunk 3GTM capabilities, UT-117S supports the voice scrambler capability. * Operating periods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90 D CHARGERS ·BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. ·BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs. ) + BC-124 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-106's are required) simultaneously. An AC adapter should be purchased separately. [. . . ]