User manual ICOM IC-F6062D

[. . . ] OPERATING GUIDE OPERATING GUIDE FOR IC-F5062D/F6062D BIIS 1200/dPMR OPERATION IMPORTANT Thank you for purchasing this Icom transceiver. The Binary Interchange of Information and Signalling (BIIS) 1200 and digital Private Mobile Radio (dPMR) system functions are built into your IC-F5062D/F6062D transceiver. NOTE: In this operating guide, the LCD illustration is shown as having characters displayed in 2 lines. INFORMATION: The 10-keypad of the optional HM-148T DTMF microphone has only the DTMF code transmitting capability, so you cannot input any ID or message with this microphone. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS OPERATING GUIDE -- This guide contains important operating instructions for: · IC-F5062D vhf dpmr mobile transceiver · IC-F6062D uhf dpmr mobile transceiver i Icom, Icom Inc. [. . . ] Ask your dealer or system operator for connection and setting details. 12 3 dPMR OPERATION Receiving a call D Receiving an Individual call q When an Individual call is received: · Rings sound. ·" " appears and the mute is released. · " " appears or blinks, depending on the pre-programmed settings. · The calling station's ID (or name) blinks. Appears Appears or blinks dPMR operation The IC-F5062D and IC-F6062D provide digital Private Mobile Radio (dPMR) operation that meets the 6. 25 kHz bandwidth requirements for narrow band operation. This increases efficiency of channel allocation and use of the spectrum. NOTE: During dPMR operation, BIIS 1200 operation is disabled. dPMR display The following displays appear in dPMR operation. CONNECT : When an acknowledgement of a Voice or Emergency call is received. OK : When an acknowledgement of a message (status message or SDM) or command (Ambience Listening, Stun, Kill, or Revive) is received. : When no acknowledgement of a call is received. : When no name is programmed, appears to the left of the calling station's ID. : When no name is programmed, appears to the left of the Talkgroup ID. ID 0000001 Calling station's ID FAILED WAIT ID TG 13 w While holding down [PTT], speak into the microphone at your normal voice level. r After the communication is finished, push [Clear] to send a `Disconnect' signal to terminate the connection. · Either station can send a `Disconnect' signal. ·" " disappears, "CLR DOWN" appears for approximately 2 seconds, and the transceiver automatically returns to the stand-by mode. CLR DOWN : When a connection is terminated. dPMR OPERATION D Receiving a Group call q When a Group call is received: · Rings sound. ·" " appears and the mute is released. · " " appears or blinks, depending on the pre-programmed settings. · The Talkgroup ID (or name) and the calling station's ID (or name) blink. · When an All Call is received, "ALL CALL" blinks instead of "TG" and the Talkgroup ID. Appears Appears or blinks 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D Receiving a status message q When a status message is received: · Rings sound. · The calling station's ID (or name) and the status message blink. The received status message RX ID STATUS 01 0000001 Calling station's ID TG ID 0100000 0000001 Calling station's ID w Push [Clear] to return to the stand-by mode. Talkgroup ID w While holding down [PTT], speak into the microphone at your normal voice level. NOTE: Only one station is allowed to speak at the same time. [. . . ] e Push [dPMR Button] again to enter the application selection mode. · "STATUS" is displayed. r Push [CH Up] or [CH Down] to select "STUN. " t Push [Call] to transmit a Stun call to the selected station. · "WAIT" is displayed while transmitting. · "OK" is displayed when an acknowledgement is received. · "FAILED" is displayed when no acknowledgment is received. r Push [CH Up] or [CH Down] to select "LISTENING. " t Push [Call] to transmit an Ambience Listening call to the selected station. · "WAIT" is displayed while transmitting. · "OK" is displayed when an acknowledgement is received, then the called station's microphone audio can be heard for the preprogrammed time period. [. . . ]