User manual ICOM IC-F610

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER UHF TRANSCEIVER iF510 iF610 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTION RWARNING!NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. [. . . ] r Repeat steps w and e to input all allowed digits. t Push [CALL] to transmit the selected TX code. u While pushing and holding [PTT], speak into the microphone at your normal voice level. i Release [PTT] to receive. IMPORTANT: To maximize the readability of your signal: (1) Pause briefly after pushing [PTT] (2) Hold the microphone 2. 5 to 5 cm from your mouth, then speak into the microphone at a normal voice level. 9 OPERATION D Tx code channel selection If the transceiver has a [TX CODE CH UP] or [TX CODE CH DN] key, the programmed Tx code channel can be selected directly. 2 D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can "customize" transceiver operation to suit your preferences and operating style. Entering the user set mode: qWhile pushing and holding [ ] and [ ], push [ ] to enter the user set mode at power ON. wPush and hold [P0] to enter user set mode. Push [P0] momentarily to select the item. Then push [ ] and [ ] to set the desired level/condition. Available set mode functions: · Backlight : AUTO, DIM, OFF or ON · Beep : ON or OFF · Beep Level : 1 to 5 or Link (links to audio output level) · SQL Level : 0 to 255 · AF Min level : 0 to 255 · Audio Filter : 3000, 3400, 0 or 300 · Mic Gain : 1 to 5 · Horn : ON or OFF e Push [ ] (or push and hold [P0]) again to exit set mode. User set mode is also available via a programmable key. 6 [SET] section. D DTMF transmission If the transceiver has a [DTMF] key, the automatic DTMF transmission function is available. q Push [DTMF]-- a DTMF code channel appears. w Push [CH UP]/[CH DN] to select the desired DTMF channel. e Push and hold [DTMF] to transmit the selected DTMF. D Scrambler function UT-109 (#02) or UT-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes. q Push and hold [SCRM] to turn the scrambler function ON. e Push [SCRM] to turn the function OFF. 10 3 [P0]; CALL BIIS OPERATION I Receiving a call D Individual call q When an individual call is received; · Beeps sound. · " " appears and the mute is released. · The programmed text message (e. g. " ") and the calling station ID (or text) is displayed alternately. · " " appears or blinks depending on the setting. I Default setting The following functions are assigned to each programmable switch as the default. : Push to send a 5-tone call or BIIS call when the selected channel is a 5-tone or MSK channel, respectively. [P1]; DIGITAL : Push to select the call list ID/transmit message, or to display the receive message record for selection. [. . . ] · HM-152T : DTMF microphone · HM-148 : Heavy duty microphone SM-25 DESKTOP MICROPHONE For base station operation. OPC-617 ACC CABLE Provides external terminal connection. OPC-822 INTERFACE CABLE Provides advanced operation, such as printer, GPS connection for position data transmission capabilities. UT-105 SmarTrunk IITM LOGIC BOARD For SmarTrunk IITM operation. UT-117/UT-117S* SmarTrunk 3GTM LOGIC BOARD For SmarTrunk 3GTM operation. [. . . ]